Mitsubishi Eclipse. Manual — part 917
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-51
81.Apply a 2 mm (0.08 inch) diameter bead of sealant
(MITSUBISHI Genuine Part number MD974421 or
equivalent) to the torque converter housing in the area
shown.
NOTE: Be sure to install the case quickly while the sealant is
wet (with 15 minutes) or leaks will occur if the rear cover is
installed after the sealant dries.
NOTE: After installation, keep the sealed area away from
the ATF for approximately one hour.
82.Install the two O-rings.
83.Install the torque converter housing and then tighten its 18
mounting bolts to the specified torque.
Tightening torque: 48
± 6 N⋅m (35 ± 4 ft-lb)
84.Insert the two O-rings into the grooves of the manual control
lever shaft.
85.Install the manual control lever shaft and parking pawl rod.
86.Align hole "A" with the groove in the manual control lever
shaft. Insert the manual control lever shaft roller into hole
"A".
AKX01077
AKX01024AB
O-RINGS
AKX01104
AKX00962
AB
PARKING
PAWL ROD
MANUAL CONTROL
LEVER SHAFT
MANUAL
CONTROL
LEVER
SHAFT
OLLER
HOLE "A"
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-52
87.Insert the new seal rings in the grooves of the accumulator
pistons.
NOTE: The piston and seal ring are common parts.
88.Identify the accumulator spring and insert it and the
accumulator piston into each hole of the transaxle case.
NOTE: Accumulator springs are identified as shown in the
illustration.
89.Install the strainer and second brake retainer oil seal.
90.Insert a new O-ring to the groove of the solenoid valve
harness connector.
91.Insert the solenoid valve harness connector into the hole
from the inside of the transaxle case so it is oriented as
shown in the illustration. Then secure the snap ring to the
connector groove.
NO. NAME
IDENTIFICATION "BLUEING"
1
For low-reverse
brake
None
2
For underdrive
clutch
Half
3
For second brake
Whole surface
4
For overdrive clutch None
AKX01078
IDENTIFICATION OF ACCUMULATOR SPRING
1
2
3
4
NOTE: THE SHADOWS ARE THE AREAS
OF IDENTIFICATION "BLUE-ING."
AB
AKX01008
4
3
2
AB
1
AKX01007AB
SECOND BRAKE
RETAINER OIL SEAL
STRAINER
AKX00961AC
SNAP RING
CONNECTOR ORIENTION
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-53
92.Install a steel ball into each of the two holes in the top face
of the valve body (outside valve body).
93.Install the valve body and gasket to the transaxle case.
Make sure that the manual valve's pin is in the groove in the
detent plate of the manual control lever.
94.Install the 27 valve body mounting bolts, and tighten to the
specified torque.
Tightening torque: 11
± 1 N⋅m (95 ± 9 in-lb)
95.Attach the solenoid valve harness to the valve body by
connecting the fluid temperature sensor and all the
connectors.
AKX01005
STEEL BALL
AH
AK100023
NO. PARTS TO BE
CONNECTED
SOLENOID VALVE HARNESS
CABLE
COLOR
CONNECTOR
HOUSING
COLOR
1
Underdrive
solenoid valve
White, red, red Black
2
Overdrive
solenoid valve
Orange, red
Black
3
Low-reverse
solenoid valve
Brown, yellow
Milky white
4
Second solenoid
valve
Blue, red, red
Milky white
5
Torque converter
clutch control
solenoid valve
Blue, yellow,
yellow
Black
AK100069AB
1
2
5
4
3
TRANSAXLE
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-54
96.Install the manual control shaft detent and tighten the bolt to
the specified torque.
Tightening torque: 6
± 1 N⋅m (52 ± 9 in-lb)
97.Apply a 2 mm (0.08 inch) diameter bead of sealant
(MITSUBISHI Genuine Part number MD974421 or
equivalent) to the valve body cover in the area shown.
NOTE: Be sure to install the case quickly while the sealant is
wet (with 15 minutes) or leaks will occur if the rear cover is
installed after the sealant dries.
NOTE: After installation, keep the sealed area away from
the ATF for approximately one hour.
98.Install the valve body cover, and then tighten its mounting
bolts to the specified torque.
Tightening torque: 11
± 1 N⋅m (95 ± 9 in-lb)
99.Install the Sealing cap and tighten the bolt to the specified
torque.
Tightening torque: 5
± 1 N⋅m (43 ± 9 in-lb)
AKX01103AB
MANUAL CONTROL
SHAFT DETENT
AKX01079
AKX01003
AK100022
SEALING CAP
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст