Mitsubishi Eclipse. Manual — part 260
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-533
STEP 19. Check connectors D-16 at intermediate
connector and D-18 at fuel tank differential pressure
sensor for damage.
Q: Are the connectors in good condition?
YES : Go to Step 20.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
STEP 20. Check the harness wire between intermediate
connector D-16 terminal 5 and fuel tank differential
pressure sensor connector D-18 terminal 1 for damage.
Q: Is the harness wire in good condition?
YES : Go to Step 22.
NO : Repair it. Then go to 22.
AC001787AD
CONNECTOR: D-16
AC103356
FUEL TANK
AD
CONNECTOR: D-18
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
AC001787AD
CONNECTOR: D-16
AC103356
FUEL TANK
AD
CONNECTOR: D-18
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-534
STEP 21. Using scan tool MB991958, check data list item
73: Fuel Tank Differential Pressure Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Disconnect hose G from the evaporative emission canister
side, and plug the hose from which the pipes have been
disconnected.
(3) Turn the ignition switch to the "ON" position.
(4) Remove the fuel cap.
(5) Set scan tool MB991958 to the data reading mode for item
73, Fuel Tank Differential Pressure Sensor.
• The fuel tank pressures should be −1.5 to 1.5 kPa
(
−0.443 to 0.443 inHg.)
(6) Connect an evaporative emission system pressure pump to
the fuel filler neck, and apply pressure.
• The scan tool reading should increase.
(7) Turn the ignition switch to the "LOCK" (OFF) position. Then
disconnect scan tool MB991958.
Q: Is the scan tool reading within the specified value?
YES : This malfunction is intermittent malfunction. Refer to
GROUP 00, How to Use Troubleshooting/Inspection
Service Points
. Then go to Step 22.
NO : Replace the ECM <M/T> or PCM <A/T>. Then go to
Step 22.
AC303127
AB
MB991911
16-PIN
MB991827
MB991824
AC002036 AC
HOSE G
AC000186
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-535
STEP 22. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern (Refer to
Diagnostic Function
− OBD-ll Drive Cycle − Procedure 1 −
Evaporative Emission System Leak Monitor
(2) Read the diagnostic trouble code.
Q: Is diagnostic trouble code P0451 set?
YES : Go to Step 2.
NO : This diagnosis is complete.
DTC P0452: Evaporative Emission Control System Pressure Sensor Low Input
AC001943
A
B
C
EVAPORATIVE EMISSION
PURGE SOLENOID
EVAPORATIVE
EMISSION CANISTER
EVAPORATIVE
EMISSION
VENTILATION
SOLENOID
FUEL TANK
CHECK VALVE A
CHECK
VALVE B
INTAKE MANIFOLD
SYSTEM DIAGRAM
D
E
F
G
I
H
L
N
M
K
J
O
P
CHAMBER
AC
FUEL TANK DIFFRENTIAL
PRESSURE SENSOR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-536
Fuel Tank Differential Pressure Sensor Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст