Mitsubishi Eclipse. Manual — part 628
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1055
.
CIRCUIT OPERATION
• The battery positive voltage is applied on the igni-
tion coil by the ignition switch-IG.
• When the ECM <M/T> or PCM <A/T> turns the
power transistor in the ECM <M/T> or PCM
<A/T> "OFF", battery positive voltage is applied
on the ignition power transistor (terminal No. 3),
and the ignition power transistor turns "ON".
• When the ignition power transistor turns on, the
ignition coil's primary circuit is grounded by the
ignition power transistor terminal No. 4. Then the
primary current flows to the ignition coil.
.
TROUBLESHOOTING HINTS (The most likely
causes for this case: )
• Malfunction of the ignition coil.
• Malfunction of the ignition power transistor.
• Improper connector contact, open circuit or
short-circuited harness wire.
• Malfunction of the ECM <M/T> or PCM <A/T>.
DIAGNOSIS
STEP 1. Check connector B-22 at distributor for damage.
Q: Is the connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
STEP 2. Check the ignition coil.
Refer to GROUP 16, Ignition System
− On-vehicle service −
Ignition coil check
Q: Are there any abnormalities?
YES : Go to Step 3.
NO : Repair the ignition coil. Then confirm that the
malfunction symptom is eliminated.
STEP 3. Check the ignition power transistor.
Refer to GROUP 16, Ignition System
− On-vehicle service −
Power transistor check
.
Q: Are there any abnormalities?
YES : Go to Step 4.
NO : Repair the ignition power transistor. Then confirm that
the malfunction symptom is eliminated.
AK300439
3
4
5
1
2
6
7
B-22 (B)
AB
CONNECTOR: B-22
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1056
STEP 4. Check the power supply voltage at distributor
connector B-22.
(1) Disconnect the connector B-22 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 5.
NO : Check connector C-07, C-89, C-108 and C-111 at
intermediate connectors for damage, and repair or
replace as required. Refer to GROUP 00E, Harness
Connector Inspection
. If intermediate
connectors are in good condition, repair harness wire
between ignition switch connector C-87 terminal 2
and distributor connector B-22 (terminal No. 1)
because of open circuit. Then confirm that the
malfunction symptom is eliminated.
STEP 5. Check the continuity at distributor harness side
connector B-22.
(1) Disconnect the connector B-22 and measure at the harness
side.
(2) Check for the continuity between terminal No. 4 and
ground.
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 6.
NO : Repair harness wire between distributor connector
B-22 (terminal No. 4) and ground because of open
circuit or harness damage. Then confirm that the
malfunction symptom is eliminated.
AK300439
3
4
5
1
2
6
7
B-22 (B)
AB
CONNECTOR: B-22
HARNESS CONNECTOR:
COMPONENT SIDE
AK000387AE
1
2
3
4
5
6
7
B-22 HERNESS
CONNECTOR:
COMPONENT SIDE
AK300439
3
4
5
1
2
6
7
B-22 (B)
AB
CONNECTOR: B-22
HARNESS CONNECTOR:
COMPONENT SIDE
AK000388AE
1
2
3
4
5
6
7
B-22 HERNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1057
STEP 6. Check connector C-51 at ECM <M/T> or connector
C-52 at PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then confirm that the
malfunction symptom is eliminated.
AK300458
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
CONNECTOR: C-52 <A/T>
C-52 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300443
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
CONNECTOR: C-51 <M/T>
C-51 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1058
STEP 7. Check for open circuit between distributor
connector B-22 (terminal No. 3) and ECM connector C-51
(terminal No. 11) <M/T> or PCM connector C-52 (terminal
No. 11) <A/T>.
Q: Is the harness wire in good condition?
YES : Go to Step 8.
NO : Repair it. Then confirm that the malfunction symptom
is eliminated.
AK300439
3
4
5
1
2
6
7
B-22 (B)
AB
CONNECTOR: B-22
HARNESS CONNECTOR:
COMPONENT SIDE
AK300458
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
CONNECTOR: C-52 <A/T>
C-52 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300443
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
CONNECTOR: C-51 <M/T>
C-51 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст