Mitsubishi Eclipse. Manual — part 102
ENGINE DIAGNOSIS
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-3
Noisy valves
Malfunction of lash adjuster (including
entry of air into high pressure chamber)
Check the lash adjuster
Thin or diluted engine oil (low engine oil
pressure)
Change the engine oil
Worn or damaged valve stem or valve
guide
Replace the valve and/or the guide
Connecting rod
noise/main bearing
noise
Insufficient oil supply
Check the engine oil level
Thin or diluted engine oil
Change the engine oil
Excessive bearing clearance
Replace the bearings
SYMPTOM
PROBABLE CAUSE
REMEDY
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-4
SPECIAL TOOLS
M1111000600544
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991958
Scan tool (MUT-III sub
assembly)
A: MB991824
Vehicle
communication
interface (V.C.I.)
B: MB991827
MUT-III USB cable
C: MB991910
MUT-III main harness
A (Vehicles with CAN
communication
system)
D: MB991911
MUT-III main harness
B (Vehicles without
CAN communication
system)
E: MB991914
MUT-III main harness
C (for Daimler
Chrysler models only)
F: MB991825
MUT-III adapter
Harness
G: MB991826
MUT-III trigger
harness
Tool not available
• Drive belt tension check
• Ignition timing check
• Curb idle speed check
• Idle mixture check
MB991668
Belt tension meter set
Tool not available
Measurement of drive belt
tension (used together with
scan tool <MUT-III Sub
Assembly>)
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
A
B
C
D
E
F
G
DO NOT USE
B991668
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-5
MB991453
Engine hanger
attachment set
MZ203827-01
When an engine lifer is
used: Supporting the
engine assembly during
removal and installation of
the transaxle
GENERAL SERVICE
TOOL
MZ203827
Engine lifter
MZ203827-01
MB991454
Engine hanger balancer
MZ203827-01
When the engine hanger is
used: Supporting the
engine assembly during
removal and installation of
the transaxle
NOTE: Special tool
MB991454 is a part of
engine hanger attachment
set MB991453.
MB991895
Engine hanger
Tool not available
MB991928
Engine hanger
A: MB991929
Joint (50)
×2
B: MB991930
Joint (90)
×2
C: MB991931
Joint (140)
×2
D: MB991932
Foot (standard)
×4
E: MB991933
Foot (short)
×2
F: MB991934
Chain and hook
assembly
Tool not available
MB990767
End yoke holder
MB990767-01
Holding the camshaft
sprocket when loosening
and tightening bolt
MD998719
Crankshaft pulley holder
pin
MT308239
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
B991453
MZ203827
B991454
MB991895
B991928
A
B
C
D
E
F
SLIDE BRACKET (HI)
B990767
D998719
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-6
MD998443
Lash adjuster holder (8)
MD998443-01
Supporting of the auto-lash
adjuster to prevent it from
falling when rocker shaft
assembly is removed or
installed
MD998713
Camshaft oil seal installer
MD998713-01
Camshaft oil seal
installation
MD998727
Oil pan remover
MD998727-01
Oil pan removal
MB991367
Special spanner
MB991367-01
Holding the crankshaft
sprocket
MD998375
Crankshaft oil seal
installer
MD998375-01
Crankshaft front oil seal
installation
MD998781
Flywheel stopper
General service tool
Flywheel <M/T> or drive
plate <A/T> supporting
MD998776
Crankshaft rear oil seal
installer
MD998776-01
Crankshaft rear oil seal
installation
MB990938
Handle
MB990938-01
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
D998443
D998713
D998727
B991367
D998781
D998776
B990938
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст