Mitsubishi Eclipse. Manual — part 206
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-317
DTC SET CONDITIONS
Logic Flow Chart
.
Check Conditions
• 60 seconds have elapsed from the start of the
previous monitoring.
• Engine coolant temperature is higher than 20°C
(68
°F).
• While the heated oxygen sensor (rear) heater is
on.
• Battery positive voltage is at between 11 and 16.5
volts.
Judgment Criteria
• Heater current of the heated oxygen sensor
(rear) heater has continued to be lower than 0.16
ampere or higher than 5.0 ampere for 4 seconds.
.
OBD-ll DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-ll Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Open or shorted heated oxygen sensor (rear)
heater circuit, or harness damage.
• Open circuit in heated oxygen sensor (rear)
heater.
• Connector damage.
• ECM failed. <M/T>
• PCM failed. <A/T>
DIAGNOSIS
Required Special Tool:
• MB991658: Test Harness
START
END
YES
YES
YES
YES
NO
NO
NO
NO
MALFUNCTION
GOOD
CONTINUOUS
FAILURE FOR 4secs
MONITORING
CONDITIONS
CURRENT < 0.16A
CURRENT > 5.0A
AK301443
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-318
STEP 1. Check connector C-23 at the heated oxygen
sensor (rear) for damage.
Q: Is the connector in good condition?
YES : Go to Step 2.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK300405
2
1
6 5 4 3
AB
C-23
HEATED OXYGEN
SENSOR (REAR)
CONNECTOR: C-23
HARNESS
CONNECTOR:
HARNESS SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-319
STEP 2. Check the heated oxygen sensor (rear).
(1) Disconnect heated oxygen sensor (rear) connector C-23
and connect test harness special tool, MB991658, to the
connector on the heated oxygen (rear) sensor side.
(2) Measure the resistance between heated oxygen sensor
connector terminal No. 5 and terminal No. 6.
Standard value: 11
− 18 ohms [at 20°C (68°F)]
Q: Is the measured resistance between 11 and 18 ohms?
YES : Go to Step 3.
NO : Replace the heated oxygen sensor (rear). Then go to
Step 12.
AK300405
2
1
6 5 4 3
AB
C-23
HEATED OXYGEN
SENSOR (REAR)
CONNECTOR: C-23
HARNESS
CONNECTOR:
HARNESS SIDE
AK000121AB
HEATED OXYGEN SENSOR
EQUIPMENT SIDE CONNECTOR
MB991658
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-320
STEP 3. Measure the power supply voltage at heated
oxygen sensor (rear) harness side connector C-23.
(1) Disconnect the connector C-23 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 3 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 5.
NO : Go to Step 4.
STEP 4. Check harness connector A-18X at the MFI relay
for damage.
Q: Is the connector in good condition?
YES : Repair harness wire between MFI relay connector
A-18X (terminal No. 4) and heated oxygen sensor
(rear) connector C-23 (terminal No. 5) because of
open circuit or short circuit to ground. Then go to Step
12.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 12.
AK300405
2
1
6 5 4 3
AB
C-23
HEATED OXYGEN
SENSOR (REAR)
CONNECTOR: C-23
HARNESS
CONNECTOR:
HARNESS SIDE
AK000322
AI
2
1
6 5 4 3
C-23 HARNESS
CONNECTOR:
COMPONENT SIDE
AK300454
2
1
3
4
CONNECTOR: A-18X
AB
A-18X
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст