Mitsubishi Eclipse. Manual — part 135
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-33
DTC SET CONDITIONS <Range/Performance problem-high input>
Logic Flow Chart
Check Conditions
• Throttle position sensor output voltage is 2 volts
or lower.
• Engine speed is lower than 2,000 r/min.
Judgement Criteria
• Volume airflow sensor output frequency has con-
tinued to be 800 Hz or higher for 2 seconds.
.
START
MONITORING
CONDITIONS
END
NO
YES
NO
YES
NO
YES
MALFUNCTION
GOOD
OUTPUT FREQUENCY
> =800Hz
CONTINUOUS
FAILURE FOR 2 secs
AK301411
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-34
DTC SET CONDITIONS <Range/Performance problem-low input>
Logic Flow Chart
Check Conditions
• Throttle position sensor output voltage is 1.5 volts
or higher.
• Engine speed is higher than 2,000 r/min.
Judgement Criteria
• Volume airflow sensor output frequency has con-
tinued to be 60 Hz or lower for 2 seconds.
.
OBD-ll DRIVE CYCLE PATTERN
Refer to Diagnostic Function
− OBD-ll Drive Cycle −
Procedure 6
.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are: )
• Volume airflow sensor failed.
• Open or shorted volume airflow sensor circuit, or
connector damage.
• ECM failed. <M/T>
• PCM failed. <A/T>
DIAGNOSIS
Required Special Tools:
• MB991958 (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: USB Cable
• MB991911: Main Harness B
START
MONITORING
CONDITIONS
END
NO
YES
NO
YES
NO
YES
MALFUNCTION
GOOD
OUTPUT FREQUENCY
< =60Hz
CONTINUOUS
FAILURE FOR 2 secs
AK301412
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-35
STEP 1. Using scan tool MB991958, check data list item 12:
Volume Airflow Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991958 to the data reading mode for item
12, Volume Airflow Sensor.
(4) Warm-up the engine to normal operating temperature: 80
°C
to 96
°C (176°F to 205°F).
• The standard value during idling should be 10 Hz or
more.
• When the engine is revved, the frequency should
increase according to the increase in engine speed.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Go to Step 2.
STEP 2. Measure the reset signal voltage at volume airflow
sensor connector B-14 by backprobing.
(1) Do not disconnect the connector B-14.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 7 and ground by
backprobing.
• Voltage should be between 6.0 and 9.0 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 6.0 and 9.0 volts?
YES : Go to Step 5.
NO : Go to Step 3.
AK300810
AB
MB991911
16-PIN
MB991827
MB991824
AK300078
3
4
5
1
2
6
7
CONNECTOR: B-14
AB
B-14 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AKX01515 AG
B-14 HARNESS
CONNECTOR:
HARNESS SIDE
1 2 3 4 5 6 7
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-36
STEP 3. Check connector B-14 at volume airflow sensor
and connector C-49 at ECM <M/T> or connector C-50 at
PCM <A/T> for damage.
Q: Is the connector in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 9.
AK300078
3
4
5
1
2
6
7
CONNECTOR: B-14
AB
B-14 (B)
HARNESS
CONNECTOR:
COMPONENT SIDE
AK300413
1
14
4
19
5
22
6
17
8
15
9
18
7
20
16
2
21
23
26
24
25
3
10
11
12
13
CONNECTOR: C-49 <M/T>
C-49 (G)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK300414
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
30
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
10
C-50 (GR)
CONNECTOR: C-50 <A/T>
AB
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст