Mitsubishi Eclipse. Manual — part 807
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-237
DTC 34 (P0768): Overdrive Solenoid Valve System
.
Solenoid Valve System Circuit
Refer to
.
CIRCUIT OPERATION
Refer to
.
DESCRIPTIONS OF MONITOR METHODS
If solenoid terminal voltage is below specified value
when shift control is not in progress, PCM judges
that overdrive solenoid has a failure.
.
MONITOR EXECUTION
Continuous
.
MONITOR EXECUTION CONDITIONS (Other
monitor and Sensor)
Other Monitor (There is no temporary DTC stored
in memory for the item monitored below)
• DTC 41 (P0731): 1st gear incorrect ratio
• DTC 42 (P0732): 2nd gear incorrect ratio
• DTC 43 (P0733): 3rd gear incorrect ratio
• DTC 44 (P0734): 4th gear incorrect ratio
• DTC 46 (P0736): Reverse gear incorrect ratio
• DTC 36 (P0743): Torque converter clutch sole-
noid malfunction
• DTC 31 (P0753): Low-reverse solenoid malfunc-
tion
• DTC 32 (P0758): Underdrive solenoid malfunc-
tion
• DTC 33 (P0763): Second solenoid malfunction
• DTC 54 (P1751): A/T control relay malfunction
Sensor (The sensor below is determined to be
normal)
• Torque converter clutch solenoid
• Low-reverse solenoid
• Underdrive solenoid
• Second solenoid
• A/T control relay
.
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-238
LOGIC FLOW CHARTS (Monitor Sequence)
.
DTC SET CONDITIONS (Entry Conditions and
Malfunction Thresholds)
Check Conditions
• Solenoid status: either solid ON or OFF.
• Shift status: in-gear.
• Voltage of battery: 10 volts or more.
Judgement Criteria
• Solenoid voltage: 3 volts or less. (0.3 second)
• If DTC 34 (P0768) is set consecutively four times,
the transaxle is locked into 3rd gear as a fail-safe
measure, and the "N" range light flashes once
per second.
.
OBD-II DRIVE CYCLE PATTERN
Start the engine, and keep the vehicle stopped in "P"
range for 5 seconds.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Malfunction of the overdrive solenoid valve
• Damaged harness or connector
• Malfunction of the PCM
AC205284
Good
Malfunction
END
START
In-gear?
Shift solenoid-D is in ON
or OFF steady state
Voltage of battery > 10 V
Solenoid circuit
voltage < 3 V
Continuous failure
for 0.3 sec.
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Overdrive solenoid valve is in
ON or OFF steady state
AB
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-239
DIAGNOSIS
Required Special Tool:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991911: MUT-III Main Harness B
STEP 1. Using scan tool MB991958, check actuator test
item 04: Overdrive Solenoid Valve.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set scan tool MB991958 to actuator test mode for item 04:
Overdrive Solenoid Valve.
• An audible clicking or buzzing should be heard when the
overdrive solenoid valve is energized.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
.
NO : Go to Step 2.
AC303127
AB
MB991911
16-PIN
MB991827
MB991824
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-240
STEP 2. Using scan tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC 54 set? (DTC 54 may be set along with multiple
DTCs).
YES : Refer to
DTC 54: A/T Control Relay
System.
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the A/T
diagnostic trouble code.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Are DTC 32 and DTC 33 set? (Multiple DTCs may be set).
YES : Go to Step 8.
NO : Go to Step 4.
AC303127
AB
MB991911
16-PIN
MB991827
MB991824
AC303127
AB
MB991911
16-PIN
MB991827
MB991824
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст