Mitsubishi Eclipse. Manual — part 559
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-779
STEP 6. Check the sensor supply voltage at ECM
connector C-62 by backprobing.
(1) Do not disconnect the ECM connector C-62.
(2) Disconnect the vehicle speed sensor connector B-39.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 80 and ground
by backprobing.
• Voltage should be between 4.8 and 5.2 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 7.
NO : Replace the ECM. Then go to Step 17.
STEP 7. Check connector C-62 at ECM for damage.
Q: Is the connector in good condition?
YES : Check connector B-36 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between vehicle speed
sensor connector B-39 (terminal No. 3) and ECM
connector C-62 (terminal No. 80) because of open
circuit. Then go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
AK300445
80
87
81
94
85
82
84
93
86
98
99
74
92
73
83
88
91
95
97 96
100
89
78
71
90
76
77
75
72
79
CONNECTOR: C-62 <M/T>
C-62 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
AK000258
71 72
73 74
78
80 81
79
82 83 84 85 86 87 88 89
75 76
91 92 93
94 95
96
98
99
97
AK000258AE
C-62 HARNESS
CONNECTOR:
HARNESS SIDE
77
90
100
AK300445
80
87
81
94
85
82
84
93
86
98
99
74
92
73
83
88
91
95
97 96
100
89
78
71
90
76
77
75
72
79
CONNECTOR: C-62 <M/T>
C-62 (GR)
AB
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-780
STEP 8. Check connector B-39 at vehicle speed sensor for
damage.
Q: Is the connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
STEP 9. Check the power supply voltage at vehicle speed
sensor harness side connector B-39.
(1) Disconnect the connector B-39 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 10.
NO : Check connectors B-36, C-28, C-78, C-112 and C-111
at intermediate connector for damage, and repair or
replace as required. Refer to GROUP 00E, Harness
Connector Inspection
. If intermediate
connectors are in good condition, repair harness wire
between ignition switch connector C-87 (terminal No.
2) and vehicle speed sensor connector B-39 (terminal
No. 1) because of open circuit or short circuit to
ground. Then go to Step 17.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01425AI
1
2
3
B-39 HARNESS
CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-781
STEP 10. Check the continuity at vehicle speed sensor
harness side connector B-39.
(1) Disconnect the connector B-39 and measure at the harness
side.
(2) Check for the continuity between terminal No. 2 and
ground.
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 11.
NO : Check connector B-36 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between vehicle speed
sensor connector B-39 (terminal No. 2) and ground
because of open circuit or harness damage. Then go
to Step 17.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01426
3 2 1
B-39 HARNESS
CONNECTOR:
COMPONENT SIDE
AR
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-782
STEP 11. Check the sensor supply voltage at vehicle speed
sensor harness side connector B-39.
(1) Disconnect the vehicle speed sensor connector B-39 and
measure at the harness side.
(2) Disconnect the combination meter connector and
auto-cruise control-ECU connector.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 3 and ground.
• Voltage should be between 4.8 and 5.2 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 12.
NO : Check connector B-36 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between vehicle speed
sensor connector B-39 (terminal No. 3) and ECM
connector C-62 (terminal No. 80) because of short
circuit to ground or harness damage. Then go to Step
17.
STEP 12. Check the vehicle speed sensor.
Refer to GROUP 54A, Combination Metres Assembly and
Vehicle Speed Sensor
− Combination Metres Assembly and
Vehicle Speed Sensor
− Inspection
.
Q: Is the vehicle speed sensor normal?
YES : Go to Step 13.
NO : Replace the vehicle speed sensor. Then go to Step
17.
STEP 13. Check connector C-62 at ECM for damage.
Q: Is the connector in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01427
3 2 1
AR
B-39 HARNESS
CONNECTOR:
COMPONENT SIDE
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст