Mitsubishi Eclipse. Manual — part 959
DOOR
TSB Revision
BODY
42-61
c. Return the drum to its original position while holding
the wires to make sure that they do not pull out.
(6) After installing the power window motor assembly to the
window regulator assembly, cut and remove the wires
witch are compressing the springs.
3. Operation check
CAUTION
• Do not operate the window regulator assembly before
installing the window glass, otherwise the limit switch
will be set.
• Window glass safety mechanism does not operate
when the window glass is closed fully at first time.
(1) Install the window glass to the window regulator
assembly.
(2) Close the window glass completely.
NOTE: Closing the window glass completely will finish
the adjustment of the limit switch.
(3) Check that the limit switch operates correctly.
.
>>B<< DOOR WINDOW GLASS INSTALLATION
1. Temporarily secure the door window glass to the door
window regulator.
2. After raising the door window glass as far as it will go, fully
secure the door window glass to the door window regulator
assembly.
INSPECTION
M1421007600268
POWER WINDOW RELAY CHECK
AC000497AB
BATTERY
CONNECTION
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
1
− 3
Less than 2 ohm
• Connect terminal 1
to the negative
battery terminal
• Connect terminal 3
to the positive
battery terminal
4
− 5
Less than 2 ohm
1
2 3
4
5
1
3
4
5
ACX01544
AC003899
AC003005
AB
POWER WINDOW
RELAY
FRONT HARNESS
RELAY BOX
DOOR
TSB Revision
BODY
42-62
DOOR HANDLE AND LATCH
REMOVAL AND INSTALLATION
M1423004600168
INSTALLATION SERVICE POINT
.
>>A<< DOOR CHECK INSTALLATION
Install the door check so that the identification mark faces
upwards.
Pre-removal Operation
• Door Trim Removal (Refer to
Post-installation Operation
• Door Inside Handle Play Check (Refer to
• Door Outside Handle Play Check (Refer to
• Door Trim Installation (Refer to
.)
• Door Fit Adjustment (Refer to
.)
AC000499
1
5.0 ± 1.0 N·m
44 ± 9 in-lb
9.0 ± 2.0 N·m
80 ± 17 in-lb
N
3
4
5
2
6
7
AB
DOOR HANDLE AND DOOR LATCH
ASSEMBLY REMOVAL STEPS
1. ETACS-ECU
2. DOOR INSIDE HANDLE
• WATERPROOF FILM (REFER TO
.)
3. DOOR OUTSIDE HANDLE
4. DOOR LOCK KEY CYLINDER
5. DOOR LOCK KEY CYLINDER
SWITCH
6. DOOR LATCH ASSEMBLY
DOOR CHECK REMOVAL STEPS
• WATERPROOF FILM (REFER TO
>>A<<
7. DOOR CHECK
DOOR HANDLE AND DOOR LATCH
ASSEMBLY REMOVAL STEPS
ITEM
IDENTIFICATION MARK
Left door
1L
Right door
1R
ACX00541
IDENTIFICATION
MARK
AB
DOOR
TSB Revision
BODY
42-63
INSPECTION
M1421007600279
DOOR LOCK ACTUATOR CHECK
ACTUATOR OPERATION CHECK <DRIVER'S SIDE>
ACTUATOR OPERATION CHECK <PASSENGER'S SIDE>
ACTUATOR SWITCH CHECK <DRIVER'S SIDE>
LEVER
POSITION
BATTERY
CONNECTION
LEVER
OPERATION
At the
"LOCK"
position
• Connect terminal 6 to
the negative battery
terminal
• Connect terminal 4 to
the positive battery
terminal
The lever moves
from the "LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position
• Connect terminal 4 to
the negative battery
terminal
• Connect terminal 6 to
the positive battery
terminal
The lever moves
from the
"UNLOCK"
position to the
"LOCK" position.
LEVER
POSITION
BATTERY
CONNECTION
LEVER
OPERATION
At the
"LOCK"
position
• Connect terminal 4 to
the negative battery
terminal
• Connect terminal 6 to
the positive battery
terminal
The lever moves
from the "LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position
• Connect terminal 6 to
the negative battery
terminal
• Connect terminal 4 to
the positive battery
terminal
The lever moves
from the
"UNLOCK"
position to the
"LOCK" position.
LEVER
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
At the "LOCK"
position
1
− 3
Less than 2 ohm
At the "UNLOCK"
position
1
− 2
Less than 2 ohm
AC000039
LOCK
UNLOCK
VIEW A
VIEW B
UNLOCK
LOCK
B
<DRIVER'S SIDE>
<PASSENGER'S SIDE>
AF
A
LEVER
LEVER
DOOR
TSB Revision
BODY
42-64
DOOR LOCK KEY CYLINDER SWITCH CHECK
<DRIVER'S SIDE>
<PASSENGER'S SIDE>
CENTER DOOR LOCK SWITCH CONTINUITY
CHECK
Remove the power window switch. (Refer to
.)
<DRIVER'S SIDE>
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
LOCK
2
− 3
Less than 2 ohm
NEUTRAL (OFF) 1
− 2 − 3
Open circuit
UNLOCK
1
− 2
Less than 2 ohm
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
LOCK
1
− 2
Less than 2 ohm
NEUTRAL (OFF) 1
− 2 − 3
Open circuit
UNLOCK
2
− 3
Less than 2 ohm
AC000500
1
2
3
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
LOCK
3
− 9
Less than 2 ohm
OFF
3
− 9 − 10
Open circuit
UNLOCK
9
− 10
Less than 2 ohm
AC000463
1 2
3 4
5 6 7 8 9 10
AB
<ECLIPSE>
AC003390
1 2
3 4
5 6 7 8 9 10
<ECLIPSE SPYDER>
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст