Mitsubishi Eclipse. Manual — part 947
WINDOW GLASS
TSB Revision
BODY
42-13
SPECIAL TOOLS
M1422000600066
WINDOW GLASS
GENERAL INFORMATION
M1422000100072
The windshield, quarter window <ECLIPSE> and lift-
gate glass <ECLIPSE> are attached by an ure-
thane-base adhesive to the window frame. This
adhesive provides improved glass holding and seal-
ing, and also permits use of body openings having a
greater structural strength.
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990480 Glass holder
General service tool
Removal and installation of
window glass
MB990449 Window
molding remover
General service tool
Removal of drip molding
MB990480
MB990449
ITEM
APPLICATION
QUANTITY
Wire (dia
× length)
For cutting adhesive
Five pieces of wire 0.6 mm
× 1 m
(0.02 in
× 3.3 ft)
Glass adhesive knife
For cutting adhesive
One
Sealant gun
For adhesive application
One
Wiping shop towels
-
As required
Sealer
For prevention of water leaks and
gathering after adhesive application
As required
3M
TM
AAD Part No. 8880 or
equivalent
For cleaning
As required
Glass holder MB990480
For holding window glass
Two
Window molding remover
MB990449
For roof drip molding removal
One
WINDOW GLASS
TSB Revision
BODY
42-14
WINDSHIELD
REMOVAL AND INSTALLATION
M1422001000335
Pre-removal and Post-installation Operation
• Front Deck Garnish Removal and Installation (Refer to GROUP 51, Windshield Wiper and Washer
• Drip Garnish Removal and Installation (Refer to GROUP 51, Garnish and Molding
.) <ECLIPSE SPYDER>
• Front Pillar Trim Removal and Installation (Refer to GROUP 52A, Trim
.)
• Headlining Removal and Installation (Refer to GROUP 52A, Headlining
• Inside Rear View Mirror Removal and Installation (Refer to GROUP 52A, Inside Rear View Mirror
AC000454
A
A
C
C
B
B
SECTION A – A
9.5 (0.4)
1.6 (0.6)
1.5 (0.1)
(Entire
circumference)
SECTION B – B
mm (in)
26 (1.0)
12 (0.5)
4
PRIMER
PRIMER
SECTION C – C
7.5 (0.3)
PRIMER
ADHESIVE: 3M™ AAD PART NO.8609 SUPER FAST URETHANE AND 3M™AAD PART NO.8608 SUPER FAST
URETHANE PRIMER OR EQUIVALENT
AB
WINDOW GLASS
TSB Revision
BODY
42-15
Required Special Tool:
• MB990480: Glass Holder
• MB990449: Window molding remover
AC000455
6
F
F
3
7
10
7
9
9
1
D
D
E
E
7
4
2
SECTION D – D
1
8, 9
2
SECTION E – E
1
2
6, 7
SECTION F – F
2
5
ADHESIVE TAPE: DOUBLE-SIDED TAPE
[6 mm (0.24 in) WIDE AND 0.125 mm (0.0049 in)
THICK]
AB
5
REMOVAL STEPS
<<A>> >>D<<
1. ROOF DRIP MOLDING <ECLIPSE>
<<B>> >>C<<
2. WINDSHIELD
>>C<<
3. GLASS STOPPER
>>C<<
4. WINDOW SPACER
>>C<<
5. SPACER
>>C<<
6. WINDSHIELD UPPER MOLDING
>>B<<
7. FRONT DRIP MOLDING CLIP A
<ECLIPSE>
>>B<<
8. FRONT DRIP MOLDING CLIP B
<ECLIPSE>
>>A<<
9. DRIP MOLDING CLIP A <ECLIPSE>
>>A<<
10. DRIP MOLDING CLIP B <ECLIPSE>
REMOVAL STEPS (Continued)
WINDOW GLASS
TSB Revision
BODY
42-16
REMOVAL SERVICE POINTS
.
<<A>> ROOF DRIP MOLDING REMOVAL
CAUTION
If the roof drip molding has become warped, should be
replaced (do not re-use).
Use special tool MB990449 to lever out the roof drip molding.
.
<<B>> WINDSHIELD REMOVAL
1. To protect the body (paint surface), apply cloth tape to all
body areas around the installed
2. Using piano wire
(1) Using a sharp-point drill, make a hole in the windshield
adhesive.
(2) Pass the piano wire from the inside of the vehicle through
the hole.
(3) Using a sharp-point drill, make a hole in the windshield
adhesive.
(4) Pass the piano wire from the inside of the vehicle through
the hole.
CAUTION
Do not let the piano wire touch the edge of the windshield.
(5) Pull the piano wire alternately from the inside and outside
along the windshield to cut the adhesive.
AC003626AB
MB990449
ACX00474 AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст