Mitsubishi Eclipse. Manual — part 692
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-49
Auto-cruise control is
not cancelled.
When brake pedal is depressed.
2
When clutch pedal is depressed. <M/T> 3
When selector lever is moved to "N"
range. <A/T>
4
When "CANCEL" switch is turned ON.
5
Auto-cruise control cannot be set.
6
Hunting (repeated acceleration and deceleration) occurs at the
set vehicle speed. <M/T>
7
Hunting (repeated acceleration and deceleration) occurs at the
set vehicle speed. <A/T>
8
Auto-cruise control indicator light inside combination meter does
not illuminate. (However, auto-cruise control is normal.)
9
SYMPTOM
INSPECTION
PROCEDURE NO.
REFERENCE PAGE
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-50
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Communication with Scan Tool MB991958 is not Possible
(Communication with the Auto-cruise Control-ECU Only is not Possible.)
AC106774
Auto-cruise Control-ECU Supply, Ground and Data Link Circuit
AB
AC001451
CONNECTOR: C-20
AB
AC101201AC
CONNECTOR: C-29
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-51
.
CIRCUIT OPERATION
Power of the auto-cruise control-ECU is transmitted
from the ignition switch (IG1) to the auto-cruise con-
trol-ECU through multi-purpose fuse 4 in the junction
block.
.
TECHNICAL DESCRIPTION (COMMENT)
The cause is probably a malfunction of the
auto-cruise control-ECU power supply circuit or the
auto-cruise control-ECU ground circuit.
.
TROUBLESHOOTING HINTS
• Damaged harness or connector.
• Malfunction of the auto-cruise control-ECU.
DIAGNOSIS
Required Special Tool:
• MB991223: Harness Set
STEP 1. Check the output circuit voltage at auto-cruise
control-ECU connector C-20 (terminal number 6) by
backprobing.
(1) Do not disconnect auto-cruise control switch connector
C-20.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 6 and ground by
backprobing.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 5.
NO : Go to Step 2.
AC103108AB
CONNECTORS: C-108, C-111
C-108
C-111
JUNCTION BLOCK
(FRONT VIEW)
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
AC103152 AB
C-20 CONNECTOR
HARNESS SIDE VIEW
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-52
STEP 2. Check auto-cruise control-ECU connector C-20.
Q: Is the connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that the malfunction is eliminated.
NO : Go to Step 3.
STEP 3. Check junction block connector C-108 and C-111.
Q: Is any connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that the malfunction is eliminated.
NO : Go to Step 4.
STEP 4. Check the harness wire between ignition switch
and auto-cruise control-ECU connector C-20 (terminal
number 6).
Q: Is any harness wire between ignition switch and
auto-cruise control-ECU connector C-20 (terminal
number 6) damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Check that the malfunction is eliminated. If the
malfunction is not eliminated, replace the auto-cruise
control-ECU (Refer to
.). Then check that the
malfunction is eliminated.
AC001451
CONNECTOR: C-20
AB
AC103108AB
CONNECTORS: C-108, C-111
C-108
C-111
JUNCTION BLOCK
(FRONT VIEW)
AC001451
CONNECTOR: C-20
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст