Mitsubishi Eclipse. Manual — part 726
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-47
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
1. Connect special tool MB991668 to the scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Turn the ignition switch to the "ON" and select scan tool
MB991958 "Belt Tension Measurement" from the menu
screen.
4. Hold special tool MB991668 (microphone) to the middle of
the drive belt between the pulleys (at the place indicated by
the arrow), about 10
− 20 mm (0.4 − 0.8 inch) away from the
rear surface of the belt and so that it is perpendicular to the
belt (within an angle of
± 15 degree angle).
CAUTION
• The temperature of the surface of the belt should be as
close as possible to underhood temperature.
• Do not let any contaminants such as water or oil get
onto the microphone.
• If strong gusts of wind blow against the microphone or
if there are any loud sources of noise nearby, the val-
ues measured by the microphone may not correspond
to actual values.
• If the microphone is touching the belt while the mea-
surement is being made, the values measured by the
microphone may not correspond to actual values.
• Do not take the measurement while the vehicle's engine
is running.
5. Gently tap the middle of the belt between the pulleys (the
place indicated by the arrow) with your finger as shown in
the illustration, and check that the vibration frequency of the
belt is within the standard value.
Standard value:
ITEM
2.4L ENGINE
3.0L ENGINE
Vibration frequency
Hz
189
− 232
142
− 168
AC303127
AB
MB991911
16-PIN
MB991827
MB991824
AKX01149AB
<2.4L ENGINE>
15˚
15˚
MB991668
(MICROP-
HONE)
10 – 20mm
(0.4 – 0.8in)
WATER
PUMP
PULLEY
CRANK
SHAFT
PULLEY
GENERATOR
PULLEY
TAP LIGHTLY
WITH A FINGER
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-48
.
AKX01150 AB
<3.0L ENGINE>
15˚ 15˚
MB991668
(MICROPHONE)
10 – 20mm
(0.4 – 0.8in)
IDLER
PULLEY
A/C COM-
PRESSOR
PULLEY
GENERATOR
PULLEY
TENSIONER
PULLEY
CRANK
SHAFT
PULLEY
TAP LIGHTLY
WITH A FINGER
AKX01150
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-49
<When using the tension gauge>
Use a belt tension gauge to check that the belt tension is within
the standard value.
Standard value:
.
ITEM
2.4L ENGINE
3.0L ENGINE
Tension N (lb)
392
− 588
(88
− 132)
490
− 686
(110
− 154)
AKX01151
AKX01151AB
TENSION GAUGE
WATER PUMP
PULLEY
CRANK-
SHAFT
PULLEY
GENERATOR
PULLEY
<2.4L ENGINE>
AKX01152
AKX01152 AB
IDLER
PULLEY
A/C COM-
PRESSOR
PULLEY
GENERATOR
PULLEY
CRANK
SHAFT
PULLEY
TENSION
GAUGE
TENSIONER
PULLEY
<3.0L ENGINE>
MAINTENANCE SERVICE
TSB Revision
GENERAL
00-50
<Belt deflection check>
Apply 98 N (22 pound) of force to the middle of the drive belt
between the pulleys (at the place indicated by the arrow) and
check that the amount of deflection in within the standard
value.
Standard value:
GENERATOR DRIVE BELT TENSION
ADJUSTMENT
.
<2.4L ENGINE>
1. Loosen the nut of the generator pivot bolt.
2. Loosen the lock bolt.
3. Turn the adjusting bolt to adjust the belt vibration frequency,
belt tension or deflection to the standard value.
Standard value:
ITEM
2.4L ENGINE
3.0L ENGINE
Deflection (Reference
value) mm (in)
6.7
− 9.0
(0.26
− 0.35)
8.5
− 10.9
(0.33
− 0.43)
AKX01153
AKX01153 AB
<2.4L ENGINE>
WATER PUMP
PULLEY
GENERATOR
PULLEY
CRANK-
SHAFT
PULLEY
98 N (22 lb)
AKX01154
AKX01154 AB
<3.0L ENGINE>
IDLER
PULLEY
A/C COM-
PRESSOR
PULLEY
GENERATOR
PULLEY
TENSIONER
PULLEY
CRANK
SHAFT
PULLEY
98 N (22 lb)
AKX01155
AKX01155 AB
ADJUSTING
BOLT
LOCK BOLT
PIVOT BOLT
<2.4L ENGINE>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст