Mitsubishi Lancer Evolution X. Manual — part 435

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-805

STEP 20. Check harness connector B-109 at starter
connector for damage.
Q: Is the connector in good condition?

YES : Go to Step 21.
NO : Repair or replace it. Refer to GROUP 00E, Harness

Connector Inspection

P.00E-2

. Then confirm that the

malfunction symptom is eliminated.

STEP 21. Measure the power supply voltage at starter
harness side connector B-109.
(1) Disconnect the connector B-109 and measure at the

harness side.

(2) Turn the ignition switch to the "START" position.
(3) Measure the voltage between terminal No. 1 and ground.

• Voltage should be battery positive voltage

(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)

present?
YES : Go to Step 26.
NO : Go to Step 22.

STEP 22. Measure the power supply voltage at starter relay
harness side connector A-28X.
(1) Disconnect the connector A-28X and measure at the

harness side.

(2) Measure the voltage between terminal No. 4 and ground.

• Voltage should be battery positive voltage

Q: Is battery positive voltage (approximately 12 volts)

present?
YES : Go to Step 23.
NO : Repair harness wire between fusible link (24) and

starter relay connector A-28X (terminal No. 4)
because of open circuit or short circuit to ground.
Then confirm that the malfunction symptom is
eliminated.

STEP 23. Check for open circuit and short circuit to
ground between starter relay connector A-28X (terminal
No. 3) and starter connector B-109 (terminal No. 1)
NOTE: Check harness after checking intermediate connector
A-39, B-17. If intermediate connector is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion

P.00E-2

. Then check that the malfunction is eliminated.

Q: Is the harness wire in good condition?

YES : Go to Step 24.
NO : Repair it. Then confirm that the malfunction symptom

is eliminated.

AK704593

1

B-109 harness
connector:
component side

AB

2

1

3
4

AK700519AC

A-28X harness
connector:
component side

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-806

STEP 24. Check harness connector B-10 at ECM connector
and harness connector C-27 at shift lever connector for
damage.
Q: Is the connector in good condition?

YES : Go to Step 25.
NO : Repair or replace it. Refer to GROUP 00E, Harness

Connector Inspection

P.00E-2

. Then confirm that the

malfunction symptom is eliminated.

STEP 25. Check for harness damage between ECM
connector B-10 (terminal No. 106) and shift lever
connector C-27 (terminal No. 7).
Q: Is the harness wire in good condition?

YES : Check harness connector C-50 at intermediate

connector for damage, and repair or replace as
required. Refer to, GROUP 00E, Harness Connector
Inspection

P.00E-2

. If intermediate connector is in

good condition, repair harness wire between shift
lever connector C-27 (terminal No. 5, No. 15) and
starter relay connector A-28X (terminal No. 2)
because of harness damage. Then confirm that the
malfunction symptom is eliminated.

NO : Repair it. Then confirm that the malfunction symptom

is eliminated.

STEP 26. Check for harness damage between starter relay
connector A-28X (terminal No. 3) and starter connector
B-109 (terminal No. 1)
NOTE: Check harness after checking intermediate connector
A-39, B-17. If intermediate connector is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector Inspec-
tion

P.00E-2

. Then check that the malfunction is eliminated.

Q: Is the harness wire in good condition?

YES : Go to Step 27.
NO : Repair it. Then confirm that the malfunction symptom

is eliminated.

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-807

STEP 27. Check for harness damage between fusible link
(24) and starter relay connector A-28X (terminal No. 4)
Q: Is the harness wire in good condition?

YES : Go to Step 28.
NO : Repair it. Then confirm that the malfunction symptom

is eliminated.

STEP 28. Check harness connector B-108 at starter
connector for damage.
Q: Is the connector in good condition?

YES : Go to Step 29.
NO : Repair or replace it. Refer to GROUP 00E, Harness

Connector Inspection

P.00E-2

. Then confirm that the

malfunction symptom is eliminated.

STEP 29. Check for open circuit and short circuit to
ground and harness damage between battery and starter
connector B-108 (terminal No. 1)
Q: Is the harness wire in good condition?

YES : Replace the starter.
NO : Repair it. Then confirm that the malfunction symptom

is eliminated.

MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS

TSB Revision

MULTIPORT FUEL INJECTION (MFI)

13A-808

Inspection procedure 26: Ignition circuit system

AK900756

1

3

2

4

1

2

3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

1 2 3

4 5 6

3 4

2

1

3 4

2

1

3 4

2

1

3 4

2

1

1

AB

IGNITION CIRCUIT

IGNITION
COIL 1

IGNITION
COIL 2

IGNITION
COIL 3

IGNITION
COIL 4

ENGINE CONTROL MODULE

3

2

3

2

3

2

3

2

4

5

20

21

4

A-39

MU802607

B-09

SPARK
PLUG

CAPACITOR

SPARK
PLUG

SPARK
PLUG

SPARK
PLUG

4

10A

A-34X

4

3

1

2

21

TO ECM

36

FUSIBLE LINK

WHITE

YELLO

W

-WHITE

GRA

Y

GRA

Y

GRA

Y

GRA

Y

WHITE-RED

WHITE-RED

WHITE-GREEN

WHITE

OFF

ON

B-02

(MU802066)

B-03

(MU802066)

B-21

(MU801211)

B-04

(MU802066)

B-06

(MU802066)

MFI
RELAY

RELAY BOX
(ENGINE COMPARTMENT)

BLA

CK

BLA

CK

BLA

CK

BLA

CK

BR

O

WN-

WHITE

BR

O

WN-

YELLO

W

BLA

CK

BLA

CK

BLACK

BLACK

BLACK

4

1

4

4

COIL
DRIVER

COIL
DRIVER

COIL
DRIVER

COIL
DRIVER

5 V

5 V

5 V

5 V