Mitsubishi Lancer Evolution X. Manual — part 10
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-65
STEP 11. Using scan tool MB991958, diagnose the CAN
bus line. (checking the AWC-ECU for internal short to
ground)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect AWC-ECU connector C-46.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-66
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between AWC-ECU
connector C-46 and joint connector (CAN2) C-104.
NO : Check AWC-ECU connector C-46, and repair if
necessary. If the AWC-ECU connector is in good
condition, replace the AWC-ECU.
STEP 12. Check the wiring harness between joint
connector (CAN2) C-104 and ETACS-ECU connector C-301
for a short to ground.
CAUTION
Disconnect the negative battery terminal. For details refer
to
.
CAUTION
A digital multimeter should be used. For details refer to
CAUTION
The test wiring harness should be used. For details refer to
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
(1) Disconnect ETACS-ECU connector and joint connector
(CAN2), and measure at the wiring harness side.
(2) Measure the resistance between joint connector (CAN2)
terminal 6 and body ground.
OK: 1 kΩ or more
AC709542 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
SAS
S-AWC
AC709543 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
J/C (1)
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
AC709707
Harness side: C-104
AT
TEST
HARNESS
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-67
(3) Measure the resistance between joint connector (CAN2)
terminal 19 and body ground.
OK: 1 kΩ or more
Q: Do all the resistances measure 1 kΩ or more?
YES : Check ETACS-ECU connector C-301, and repair if
necessary. If the ETACS-ECU connector is in good
condition, replace the ETACS-ECU.
NO : Repair the wiring harness between ETACS-ECU
connector C-301 and joint connector (CAN2) C-104.
STEP 13. Using scan tool MB991958, diagnose the CAN
bus line. (checking the ASC-ECU for internal short to
ground)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect ASC-ECU connector A-05.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
AC709707AU
TEST
HARNESS
Harness side: C-104
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-68
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between ASC-ECU
connector A-05 and joint connector (CAN3) C-127.
NO : Check ASC-ECU connector A-05, and repair if
necessary. If the ASC-ECU connector is in good
condition, replace the ASC-ECU.
STEP 14. Using scan tool MB991958, diagnose the CAN
bus line. (checking the ECM for internal short to ground)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect ECM connector B-10.
AC709542 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
SAS
S-AWC
AC709543 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
J/C (1)
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст