Mitsubishi Lancer Evolution X. Manual — part 229
STEERING WHEEL
TSB Revision
POWER STEERING
37-31
<<B>>DRIVER’S AIR BAG MODULE CONNECTOR
DISCONNECTION
Slide the outer housing of the driver’s air bag module connector
in the arrow direction shown and disconnect the connector.
.
<<C>> DRIVER’S AIR BAG MODULE REMOVAL
CAUTION
• Never use an electric tester to diagnose the air bag
module circuit. Never attempt to disassemble the air
bag module.
• Store the removed air bag module in a clean, dry place
with the pad surface facing upward.
• When discarding the air bag module, deploy the air bag
as specified in the service procedure. (Refer to GROUP
52B − Air bag module and seat belt pre-tensioner dis-
posal procedure
• With the driver's air bag module mounting torx screw,
loosen the screw, but do not remove it.
Using the torx wrench (T30), remove the driver's air bag mod-
ule.
.
AC605948
AC600868
AI
Lower column cover
Driver's air bag
module connector
(4-pin, yellow)
Horn connector
Outer housing of the
driver's air bag module connector
AC704972 AB
Equal to or more than
40mm (1.6 inch).
STEERING WHEEL
TSB Revision
POWER STEERING
37-32
<<D>> STEERING WHEEL ASSEMBLY REMOVAL
1. Position the steering wheel in a straight ahead position.
CAUTION
• Use the special tool to remove the steering wheel since
the steering column collision adsorbing mechanism
may be damaged.
2. Use special tool MB990803 to remove the steering wheel.
INSTALLATION SERVICE POINTS
.
>>A<< STEERING WHEEL ASSEMBLY/DRIVER'S
AIR BAG MODULE INSTALLATION
After centering the clock spring (Refer to 52B − Air bag module
clock spring ), install the steering wheel assembly.
.
>>B<<DRIVER’S AIR BAG MODULE CONNECTOR
CONNECTION/STEERING SWITCH CONNECTOR
CONNECTION/HORN CONNECTOR
CONNECTION
Connect the connector securely and route the harnesses not to
lie off the cover hole.
AC705717AB
MB990803
STEERING SHAFT
TSB Revision
POWER STEERING
37-33
STEERING SHAFT
REMOVAL AND INSTALLATION
M1372011501376
CAUTION
• Before removing the steering wheel assembly and driver's air bag module/knee air bag module,
always refer to GROUP 52B − Service Precautions
and Driver’s Air bag Module and Clock
Spring
or Knee Air bag Module
.)
• After installation, perform a calibration for the ASC-ECU to learn the steering wheel sensor neutral
point. (Refer to GROUP 35C − On-vehicle Service − Steering Wheel Sensor Calibration
Pre-removal Operation
• Steering Wheel at Straight-ahead Position Check
• Steering Wheel Assembly Removal (Refer to
.)
• Instrument Panel Cover Lower Removal (Refer to
GROUP 52A − Instrument Lower Panel
.) <MR>
• Knee Air Bag Module Removal (Refer to GROUP 52B −
Knee Air Bag Module
.)
Post-installation Operation
• Instrument Panel Cover Lower Installation (Refer to
GROUP 52A − Instrument Lower Panel
.) <MR>
• Steering Wheel Assembly Installation (Refer to
.)
• Steering Wheel at Straight-ahead Position Check
AC709222 AG
4
8
3
2
6
1
7
10
2.5 ± 0.5 N·m
22 ± 4 in-lb
12 ± 3 N·m
106 ± 27 in-lb
28 ± 7 N·m
21 ± 5 ft-lb
4
3
9
A
A
4
3
4
3
7.0 ± 3.0 N·m
62 ± 27 in-lb
5
Section A-A
Claw
Section C-C
Claw
Section B-B
Claw
Note: claw position is symmetrical
20 ± 5 N·m
15 ± 4 ft-lb
2.5 ± 0.5 N·m
22 ± 4 in-lb
B
B
C
C
Removal steps
<<
A
>>
1. Knob cap <Vehicles with
KOS>
2. Ignition key cover
3. Steering column lower cover
•
Receiver antenna module
removal (Refer to GROUP
42B − Exterior Transmitter
Antenna Assembly, Interior
Transmitter Antenna
Assembly, Receiver Antenna
Module
<Vehicles with KOS>
Removal steps (Continued)
STEERING SHAFT
TSB Revision
POWER STEERING
37-34
REMOVAL SERVICE POINTS
.
<<A>> KNOB CAP REMOVAL
Remove the knob cap while pressing the two projections.
.
<<B>> STEERING SHAFT COVER REMOVAL
1. Remove the clip (for securing the floor carpet), and turn
back the floor carpet.
2. Remove the clip (for securing the steering shaft cover), and
then remove the steering shaft cover.
.
•
WCM removal (Refer to
GROUP 42C − WCM
.) <Vehicles with
WCM>
4. Steering column upper cover
5. Paddle shift assembly
<Vehicles with paddle shift>
6. Clock spring column switch
assembly
7. Key interlock cable (Refer to
GROUP 22C − Key interlock
and shiftlock mechanisms
<<
B
>>
8. Steering shaft cover
>>
B
9. Steering column bolt (steering
column shaft assembly and
steering gear and linkage
connection)
<<
C
>>
>>
A
10. Steering column shaft
assembly
Removal steps (Continued)
AC609624 AB
Clip
(Lock cover steering shaft)
Steering shaft cover
Clip
(Lock floor carpet)
Tear off
floor carpet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст