Mitsubishi Lancer Evolution X. Manual — part 632
CONTROL HOUSING
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-41
DISASSEMBLY SERVICE POINTS
.
<<A>> LOCK PIN REMOVAL
Drive out the lock pin in the direction shown.
.
<<B>> OIL SEAL REMOVAL
Using special tool, MD999566, remove the oil seal.
.
<<C>> SLIDE BALL BEARING REMOVAL
Using special tool, MB990947, remove the slide ball bearing.
ASSEMBLY SERVICE POINTS
.
>>A<< SLIDE BALL BEARING INSTALLATION
Using special tool, MB990984, install the slide ball bearing in
alignment with the control housing end face taking care not to
let the bearing protrude to the oil seal installing surface.
AK703310
AK703311AC
MD999566
AK703384AC
MB990947
Slide ball bearing
AK703367AC
MB990984
CONTROL HOUSING
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-42
.
>>B<< OIL SEAL INSTALLATION
1. Using special tool, MB991246, install the oil seal.
2. Apply specified transmission oil to the oil seal lip area.
Specified transaxle oil: Mitsubishi Genuine DiaQueen
New Multi Gear oil SAE 75W-80 (GL-3)
.
>>C<< LOCK PIN INSTALLATION
Drive the lock pin all the way into place to the end face from the
illustrated direction.
.
>>D<< STOPPER BRACKET INSTALLATION
Tighten the stopper bracket mounting bolts to the specified
torque in the illustrated order.
AK703312AC
MB991246
AK703310
AK703385AC
1
3
2
SELECT LEVER
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-43
SELECT LEVER
DISASSEMBLY AND ASSEMBLY
M1222012800386
ASSEMBLY SERVICE POINTS
.
>>A<< SELECT LEVER SHOE INSTALLATION
Apply specified grease to the sliding contact surface of the
select lever shoe.
Specified grease: Mitsubishi Part No. 0101011 or
equivalent
AK703152
1
4
5
6
7
8
9
10
3
2
AC
11 ± 2 N·m
97 ± 17 in-lb
Removal steps
1.
Dust cover
2.
Nut
3.
Spring washer
4.
Washer
5.
Select lever bushing
6.
Select lever bracket
7.
Select lever bushing
8.
Dust cover
9.
Select lever
>>A<<
10. Select lever shoe
Removal steps (Continued)
AK703386
AC
Select lever shoe
CLUTCH HOUSING
TSB Revision
MANUAL TRANSAXLE OVERHAUL
22B-44
CLUTCH HOUSING
DISASSEMBLY AND ASSEMBLY
M1222003700660
NOTE: *Refer to the assembly service points only
when the clutch housing is replaced.
Required Special Tools:
• MB991946: Ply bar
• MB990883: Rear suspension bushing arbor
• MD999547: Oil seal installer
• MB992271: Oil seal installer
• MB992075: Handle
AK702515
1
2
6
5
4
9*
AC
3
7*
8*
10
10 ± 2 N·m
88 ± 17 in-lb
Removal steps
1. Clutch release bearing retainer
>>D<<
2. Oil seal
3. Maintenance hole cover
4. Cover A
5. Cover B
<<A>>
>>C<<
6. Output front oil guide
>>B<<
7. Oil tank cover (CHG)*
>>B<<
8. Oil tank cover (REV)*
>>A<<
9. Slide ball bearing (for shift rail)*
10. Clutch housing
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст