Mitsubishi Lancer Evolution X. Manual — part 507
ON-VEHICLE SERVICE
TSB Revision
MANUAL TRANSAXLE
22A-121
5. Rotate the steering wheel 180° or more to the right or left,
and drive the vehicle at 20 km/h or less to check that the
tight corner braking phenomenon occurs.
NOTE:
.
•
The occurrence levels of body vibration and noise
caused by the tight corner braking phenomenon will dif-
fer depending on the conditions of tire and road surface.
•
If the tight corner braking phenomenon does not occur,
the system may have an abnormality. Therefore, check
the hydraulic pressure.
HYDRAULIC PRESSURE CHECK
M1221011800089
1. Remove the rear wheel (RH), then remove the rear wheel
splash shield.(Refer to GROUP 42A − Splash shield
.)
2. Raise the vehicle.
3. Disconnect the hydraulic unit from the ACD pressure tube
assembly. Then, connect the special tool below to the
hydraulic unit side.
• Hose adapter (MB991705)
• Oil pressure gauge (MD998330)
4. Bleed the system. (Refer to
CAUTION
Before connecting or disconnecting scan tool, always turn
the ignition switch to the LOCK (OFF) position.
5. Connect scan tool to the data link connector. (Refer to
.)
6. Turn the ignition switch to the "ON" position.
7. Perform the actuator test (item No. 05) of scan tool to
forcibly activate ACD.
NOTE:
.
•
The forced activation (item No. 05: ACD operation check
mode) is continued for 1 minute, then it will be canceled
automatically. Also, using the clear key on the scan tool,
the activation can be forcibly canceled.
•
When the ACD functions are stopped due to the
fail-safe, the forced activation cannot be performed.
CAUTION
During the hydraulic pressure check, fill the fluid so that
the fluid constantly remains in the oil reservoir.
8. Check that the generated hydraulic pressure of the hydraulic
unit is within the standard value.
Standard valve: 0.9 − 1.1 MPa (130 − 159 psi)
9. If the measured value exceeds the standard value, replace
the hydraulic unit.
10.After applying oil to the flare nut thread of ACD pressure
tube assembly, connect the assembly to the hydraulic unit,
then tighten to the specified torque.
Tightening torque: 26 ± 4 N⋅ m (19 ± 3 ft-lb)
11.Perform the air bleeding. (Refer to
AC707692AC
MB991705
MD998330
TRANSAXLE CONTROL
TSB Revision
MANUAL TRANSAXLE
22A-122
TRANSAXLE CONTROL
REMOVAL AND INSTALLATION
M1221003801106
AC705547
N
1
2
12
11
10
3
4
5
9
6
AC
8
7
7.0 ± 3.0 N·m
62 ± 26 in-lb
9.5 ± 3.5 N·m
85 ± 30 in-lb
Shift lever assembly
removal steps
1. Shift knob
•
Floor console bracket (A)
(Refer to GROUP 52A, Floor
console assembly
2. Select cable connection (shift
lever side)
>>
B
<<
3. Shift cable connection (shift
lever side)
4. Harness clip connection
5. Connector connection
6. Shift lever assembly
Shift cable and select cable
assembly removal steps
1. Shift knob
•
SRS-ECU (Refer to GROUP
52B, SRS-ECU
.)
•
G and yaw rate sensor and G
and yaw rate sensor bracket
(Refer to GROUP 35C − G and
Yaw Rate Sensor
.)
2. Select cable connection (shift
lever side)
>>
B
<<
3. Shift cable connection (shift
lever side)
•
Air cleaner assembly (Refer to
GROUP 15, Air cleaner
.)
•
Engine control harness
connector bracket (Refer to
GROUP 54A, Battery
.)
7. Snap pin
8. Washer
9. Shift cable connection
(transaxle side)
<<
A
>>
>>
A
<<
10. Select cable connection
(transaxle side)
<<
A
>>
>>
A
<<
11. Clip
12. Shift cable and select cable
assembly
Shift cable and select cable
assembly removal steps
TRANSAXLE CONTROL
TSB Revision
MANUAL TRANSAXLE
22A-123
REMOVAL SERVICE POINT
.
<<A>> SELECT CABLE CONNECTION (TRAN-
SAXLE SIDE) / CLIP REMOVAL
1. Set the select cable clips to a status shown in the figure,
then disconnect the cable.
2. Push down the clip claw using a screwdriver or others.
Then, remove the clip together with the cable from the
bracket.
AC707727
Clip
Select cable
AC
AC210556
Clip
Shift cable,
select cable
Claws
AE
TRANSAXLE CONTROL
TSB Revision
MANUAL TRANSAXLE
22A-124
INSTALLATION SERVICE POINTS
.
>>A<< CLIP/SHIFT CABLE CONNECTION (TRAN-
SAXLE SIDE)/SELECT CABLE CONNECTION
(TRANSAXLE SIDE) INSTALLATION
CAUTION
Securely insert the clip, shift cable, and select cable until
they click into place.
1. After inserting the new clip into the cable bracket, insert the
shift cable or select cable into the cable bracket.
NOTE: The clip can be installed either with its face side down
or under side down.
2. After assembling the clip of select cable as shown in the
figure, connect the cables to the levers.
.
AC210558
Shift cable, select cable
New clip
Cable bracket
AG
AC402309
Clip
AE
Select cable
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст