Mitsubishi Lancer Evolution X. Manual — part 212
SPECIAL TOOL
TSB Revision
PARKING BRAKES
36-7
SPECIAL TOOL
M1361000600101
Tool
Tool number and
name
Supersession
Application
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III sub
assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB
cable
c. M.U.T.-III main
harness A
(Vehicles with
CAN
communication
system)
d. M.U.T.-III main
harness B
(Vehicles without
CAN
communication
system)
e. M.U.T.-III main
harness C (for
Daimler Chrysler
models only)
f. M.U.T.-III
measurement
adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
Actuator test check
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
a
b
c
d
e
f
g
DO NOT USE
ON-VEHICLE SERVICE
TSB Revision
PARKING BRAKES
36-8
ON-VEHICLE SERVICE
PARKING BRAKE LEVER STROKE CHECK AND
ADJUSTMENT
M1361000900834
.
STROKE CHECK [CONTROL FORCE:
APPROXIMATELY 200 N (45 POUNDS)]
Standard value: 3 to 5 notches
.
STROKE ADJUSTMENT
If the parking brake lever stroke is out of the standard range,
adjust as described below:
1. Remove the floor console box cup holder (Refer to GROUP
52A − Floor Console Assembly
).
2. Loosen the adjusting nut to the end of the cable rod in order
to allow slack in the cables.
3. Remove the rear brake disk adjusting hole plug. Then insert
a flat-tipped screwdriver to turn the adjuster to the arrow
direction (to expand the shoe) until the parking brake shoe
makes contact and the disk can no longer be turned. Back
off the adjuster to the opposite direction by five notches.
CAUTION
Be careful that the parking brake lever notch number
should be within the standard range. If the notch number
is too low, rear brake dragging can be caused.
4. Adjust the parking brake lever stroke to the standard value
by turning the adjusting nut. After adjustment, check that
there is no free play between the adjusting nut and the
parking brake lever.
5. After adjusting the parking brake lever stroke, release the
parking brake. Then turn the rear wheels to check that the
rear brakes are not dragging.
6. Install the floor console box cup holder. (Refer to GROUP
52A − Floor Console Assembly
.)
AC609684AB
Adjusting nut
Cable rod
AC202320 AB
Adjuster
ON-VEHICLE SERVICE
TSB Revision
PARKING BRAKES
36-9
PARKING BRAKE SWITCH CHECK
M1361003301124
CAUTION
Do not apply grease or lubricant to the switch and the
switch installation section to avoid malfunction of the
switch. In addition, do not use gloves which have grease
on them.
1. Remove the floor console assembly (Refer to GROUP 52A −
Floor Console
2. Check for continuity between the parking brake switch
terminal and the switch mounting bolt.
3. After the check, install the floor console assembly. (Refer to
.)
PARKING BRAKE LINING SEATING PROCEDURE
M1361005100145
CAUTION
Perform lining seating in a place with good visibility, and
pay special attention to safety.
Perform lining seating by the following procedure when replac-
ing the parking brake shoe assemblies or the rear brake disks,
or when brake performance is insufficient.
1. Adjust the parking brake lever stroke to the standard value
2. Set a spring scale to the center of the parking brake lever
grip. Then, pull the parking brake lever to the vertical
direction of the lever with a force of approximately 100 N (22
pounds).
3. Drive the vehicle at a constant speed of 35 − 50 km/h (22 -
31 mph) for 100 meters (328 feet).
4. Release the parking brake and let the brakes cool for five to
ten minutes.
5. Repeat the procedure in steps 2 to 4 four or five times.
Check condition
Normal condition
When parking brake
lever is pulled.
Continuity exists
(2 Ω or less)
When parking brake
lever is released.
No continuity
AC609685
AC604651AD
Spring scale
Pull
Approximately
40 mm (1.57 inch)
PARKING BRAKE LEVER
TSB Revision
PARKING BRAKES
36-10
PARKING BRAKE LEVER
REMOVAL AND INSTALLATION
M1361001301021
CAUTION
Do not apply grease or lubricant to the switch and the switch installation section to avoid malfunction
of the switch. In addition, do not use gloves which have grease on them.
Pre-removal operation
Floor console assembly removal (Refer to GROUP 52A −
Floor Console Assembly
Post-installation operation
• Parking brake lever stroke check and adjustment (Refer
).
• Floor console assembly installation (Refer to GROUP 52A
− Floor Console Assembly
AC807091AB
A
B
B
C
D
D
1
3
5
4
2
C
A
N
Section A – A
Section B – B
Section C – C
Section D – D
20 ± 5 N·m
15 ± 3 ft-lb
20 ± 5 N·m
15 ± 3 ft-lb
Removal steps
•
Release the parking brake lever.
•
Loosen the adjusting nut.
1. Parking brake switch connector
connection
<<
A
>>
>>
A
2. Parking brake rear cable
connection
3. Parking brake lever assembly
4. Parking brake switch
5. Adjusting nut
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст