Mitsubishi Lancer Evolution X. Manual — part 17
![](/vehicles/winoney/ifonan/iri/dmisane.png)
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-93
STEP 15. Using scan tool MB991958, diagnose the CAN
bus line. (checking the shift lever for internal short to
ground)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect shift lever connector C-27.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
![](/vehicles/winoney/ifonan/iri/heoou.png)
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-94
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between shift lever
connector C-27 and joint connector (CAN3) C-127.
NO : Check shift lever connector C-27, and repair if
necessary. If the shift lever connector is in good
condition, replace the shift lever.
AC709542 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
SAS
S-AWC
AC709543 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
J/C (1)
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
![](/vehicles/winoney/ifonan/iri/fochaco.png)
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-95
STEP 16. Using scan tool MB991958, diagnose the CAN
bus line. (checking the TC-SST-ECU for internal short to
ground)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect transaxle assembly connector B-107.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
![](/vehicles/winoney/ifonan/iri/hohesth.png)
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-96
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between transaxle
assembly connector B-107 and joint connector
(CAN4) A-14.
NO : Check transaxle assembly connector B-107, and
repair if necessary. If the transaxle assembly
connector is in good condition, replace the transaxle
assembly.
AC709542 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
ENGINE
J/C (1)
ETACS
<M/T>
SAS
S-AWC
AC709543 AC
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
ASC
LEVER
J/C (1)
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст