Mitsubishi Lancer Evolution X. Manual — part 542
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-125
DTC SET CONDITIONS <TARGET
CLUTCH 2 (EVEN) PRESSURE: 3,000 HPA
OR MORE>
Check Conditions
• Engine speed: 650 r/min or more.
• Time since above engine condition: 1.5 seconds
or more.
• Clutch 2 (even) state: Slip or engaged.
• Target clutch 2 (even) pressure: 3,000 hPa or
more.
JUDGMENT CRITERIA
• Calculated pressure: −5,000 hPa or less. (Time
required
*
)
*: Time required
The time required for the "Rationality-high" monitor depends on the transmission fluid temperature, the shift
lever position.
Example of the time required
i) When the shift lever position is P: The time required is always 220 msec.
ii) When the shift lever position is "R → N":
If the transmission fluid temperature is -10 ° C (14 ° F) or more, the time required is 1,220 msec.
If the transmission fluid temperature is lower than -10 ° C (14 ° F), the time required is 2,220 msec.
iii) When shift lever position is D:
If the transmission fluid temperature is -10 ° C (14 ° F) or less, the time required is 3,220 msec.
If the transmission fluid temperature is higher than -10 ° C (14 ° F), the time required is 2,220 msec.
.
Shift lever position
Transmission fluid temperature
Time required
"D → N" or "R → N" or "R → P"
>= -10 ° C (14 ° F)
1,220 msec
< -10 ° C (14 ° F)
2,220 msec
"N" or "P"
All range
220 msec
"R" or "D" or manual mode
<= -10 ° C (14 ° F)
3,220 msec
> -10 ° C (14 ° F)
2,220 msec
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-126
OBD-II DRIVE CYCLE PATTERN <TARGET
CLUTCH 2 (EVEN) PRESSURE: 3,000 HPA
OR MORE>
The calculated pressure remains −5,000 hPa or more
for time required
*
.
*: Time required
The time required for the "Rationality-high" monitor depends on the transmission fluid temperature, the shift
lever position.
Example of the time required
i) When the shift lever position is P: The time required is always 220 msec.
ii) When the shift lever position is "R → N":
If the transmission fluid temperature is -10 ° C (14 ° F) or more, the time required is 1,220 msec.
If the transmission fluid temperature is lower than -10 ° C (14 ° F), the time required is 2,220 msec.
iii) When shift lever position is D:
If the transmission fluid temperature is -10 ° C (14 ° F) or less, the time required is 3,220 msec.
If the transmission fluid temperature is higher than -10 ° C (14 ° F), the time required is 2,220 msec.
.
Shift lever position
Transmission fluid temperature
Time required
"D → N" or "R → N" or "R → P"
>= -10 ° C (14 ° F)
1,220 msec
< -10 ° C (14 ° F)
2,220 msec
"N" or "P"
All range
220 msec
"R" or "D" or manual mode
<= -10 ° C (14 ° F)
3,220 msec
> -10 ° C (14 ° F)
2,220 msec
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-127
LOGIC FLOW CHARTS (Monitor Sequence) <Target clutch 2 (even) pressure: 1,400
hPa or more to 3,000 hPa or less>
.
AC805098
*: Time required
The time required for the "Rationality-high" monitor depends on the transmission fluid temperature,
the shift lever position.
Example of the time required
i) When the shift lever position is P: The time required is always 220 msec.
ii) When the shift lever position is "R -> N":
If the transmission fluid temperature is -10˚C (14˚F) or more, the time required is 1,220 msec.
If the transmission fluid temperature is lower than -10˚C (14˚F), the time required is 2,220 msec.
iii) When shift lever position is D:
If the transmission fluid temperature is -10˚C (14˚F) or less, the time required is 3,220 msec.
If the transmission fluid temperature is higher than -10˚C (14˚F), the time required is 2,220 msec.
Shift lever position
Transmission fluid temperature
Time required
"D N" or "R N" or "R P"
"N" or "P"
"R" or "D"
>= -10˚C (14˚F)
< -10˚C (14˚F)
<= -10˚C (14˚F)
> -10˚C (14˚F)
All range
1,220 msec
2,220 msec
220 msec
3,220 msec
2,220 msec
START
No
Good
Malfunction
END
Monitoring condition met
No
Yes
Yes
Yes
No
Calculated pressure
< -2,000 mbar
Continuous failure
for time required*
hPa
"R" or "D" or manual mode
AB
DIAGNOSIS <TC-SST>
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-128
DTC SET CONDITIONS <TARGET
CLUTCH 2 (EVEN) PRESSURE: 1,400 HPA
OR MORE TO 3,000 HPA OR LESS>
Check Conditions
• Engine speed: 650 r/min or more.
• Time since above engine condition: 1.5 seconds
or more.
• Clutch 2 (even) state: Slip or engaged.
• Target clutch 2 (even) pressure: 1,400 hPa or
more.
JUDGMENT CRITERIA
• Calculated pressure: −2,000 hPa or less. (Time
required
*
)
*: Time required
The time required for the "Rationality-high" monitor depends on the transmission fluid temperature, the shift
lever position.
Example of the time required
i) When the shift lever position is P: The time required is always 220 msec.
ii) When the shift lever position is "R → N":
If the transmission fluid temperature is -10 ° C (14 ° F) or more, the time required is 1,220 msec.
If the transmission fluid temperature is lower than -10 ° C (14 ° F), the time required is 2,220 msec.
iii) When shift lever position is D:
If the transmission fluid temperature is -10 ° C (14 ° F) or less, the time required is 3,220 msec.
If the transmission fluid temperature is higher than -10 ° C (14 ° F), the time required is 2,220 msec.
.
Shift lever position
Transmission fluid temperature
Time required
"D → N" or "R → N" or "R → P"
>= -10 ° C (14 ° F)
1,220 msec
< -10 ° C (14 ° F)
2,220 msec
"N" or "P"
All range
220 msec
"R" or "D" or manual mode
<= -10 ° C (14 ° F)
3,220 msec
> -10 ° C (14 ° F)
2,220 msec
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст