Mitsubishi Lancer Evolution X. Manual — part 612
TRANSMISSION CONTROL
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-405
REMOVAL SERVICE POINT
.
<<A>> PULL RING REMOVAL
1. Pull the pull ring upward as shown in the figure. (Carry out
the following operation with the pull ring pulled upward.)
2. Raise the claw using a precision screwdriver.
3. Remove the pull ring by turning it clockwise, and pull it out
upward.
>>
A
8. Transaxle control cable
connection (transaxle side)
9. Transaxle control cable
bracket
10. Transaxle control cable
Transaxle control cable
removal steps (Continued)
AC902247
AD
AC902248
Precision
screwdriver
Claw
AC
Claw
AC902249
Clockwise
AD
AC902250
AC
TRANSMISSION CONTROL
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-406
INSTALLATION SERVICE POINTS
.
>>A<< TRANSAXLE CONTROL CABLE (TRAN-
SAXLE SIDE/SHIFT LEVER SIDE) INSTALLATION
1. Connect the transaxle control cable (shift lever side) to the
shift lever assembly.
2. Operate the lever so that the shift control lever positioning
mark is set to the N position.
3. Move the slider of the transaxle control cable (transaxle
side) tip to the direction A to pull up the lock piece to the
direction B.
4. Install the transaxle control cable (transaxle side) in the
transaxle control cable bracket at the top of transaxle.
5. Move the shift lever to the N⇔D position three times or
more, and shift to the N position.
6. Connect the transaxle control cable to the shift control lever,
and firmly push down the lock piece of transaxle control
cable to lock it.
NOTE:
.
•
The slider automatically returns to the fixed position by
the spring.
•
The lock position of transaxle control cable is automati-
cally adjusted by a spring.
.
AC707764
P
N
D
AC
Shift control lever
Mark
Shift control lever
AC707742
AD
Shift control
lever
Lock piece
Slider
Transaxle
control cable
A
B
AC707743
AD
Shift control
lever
Lock piece
Slider
Transaxle
control cable
TRANSMISSION CONTROL
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-407
>>B<< KEY INTERLOCK CABLE INSTALLATION
CAUTION
Leave the ignition switch in the LOCK (OFF) position until
the key interlock cable installation is completed.
1. Move the shift lever to the P position, and turn the ignition
switch to the LOCK (OFF) position.
2. Install the tip of key interlock cable to the lock cam pin of
shift lever assembly, using a caution not to twist the inner
cable.
3. Install the adjuster case with its lock guide pulled up
(unlocked).
4. With the lock cam pin pushed in the direction B as shown in
the figure to remove the slack from the key interlock cable,
securely lower the lock guide and lock it.
NOTE: The lock position of the key interlock cable is auto-
matically adjusted by a spring.
.
>>C<< PULL RING INSTALLATION
1. With the A in the figure raised, install the pull ring by turning
it counterclockwise.
AC900053
View A
Key inter
lock cable
A
Adjuster case
Inner cable
Lock guide
AC
Spring
Lock
Adjuster case
Lock guide
Unlock
B
Lock cam pin
AC902249
Counterclockwise
AE
Pull ring
A
KEY INTERLOCK AND SHIFT LOCK MECHANISMS
TSB Revision
TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)
22C-408
KEY INTERLOCK AND SHIFT LOCK MECHANISMS
REMOVAL AND INSTALLATION
M1225009800170
Pre-removal Operation
• Floor console bracket (A) and floor console side cover
removal (Refer to GROUP 52A − Floor Console Assembly
• Instrument panel cover lower removal <Leather combina-
tion interior package (Vehicles without side air bag)>
(Refer to GROUP 52A − Instrument Lower Panel
.)
• Steering column lower cover removal (Refer to GROUP
37 − Steering Shaft
• Foot duct (driver's side) removal (Refer to GROUP 55 −
Duct
Post-installation Operation
• Foot duct (driver's side) installation (Refer to GROUP 55 −
• Steering column lower cover installation (Refer to GROUP
37 − Steering Shaft
• Instrument panel cover lower installation <Leather combi-
nation interior package (Vehicles without side air bag)>
(Refer to GROUP 52A − Instrument Lower Panel
.)
• Floor console bracket (A) and floor console side cover
installation (Refer to GROUP 52A − Floor Console Assem-
bly
• Key interlock mechanism check (Refer to
• Shift lock mechanism check (Refer to
.)
• Shift lever operation check (Refer to
AC705527
AC709660AB
2
1
5
3
4
Removal steps
1.
Band clip
2.
Wiring harness clip
>>
B
3.
Key interlock cable
connection (shift lever side)
<<
A
>>
>>
A
4.
Key interlock cable
connection (steering side)
5.
Key interlock cable
Removal steps
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст