Mitsubishi Lancer Evolution X. Manual — part 615

TRANSAXLE ASSEMBLY

TSB Revision

TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)

22C-417

5. Connect the transaxle control cable to the shift control lever,

and firmly push down the lock piece of transaxle control
cable to lock it.
NOTE:

.

•

The slider automatically returns to the fixed position by
the spring.

•

The lock position of transaxle control cable is automati-
cally adjusted by a spring.

.

>>D<< TRANSMISSION FLUID REFILLING

CAUTION

Refill 6.1 dm

3

(6.4 qt) of the transmission fluid.

NOTE: The fluid capacity of the oil cooler assembly and the oil
cooler hose is 0.6 dm

3

(0.6 qt).

CAUTION

• If the transaxle assembly is repaired, fill new fluid and

check the transmission fluid level. (Refer to

P.22C-398

.)

• When the transaxle assembly is not repaired, the

drained fluid can be reused if it is between the replace-
ment intervals.

AC707743

AD

Shift control
lever

Lock piece

Slider

Transaxle
control cable

OIL PAN

TSB Revision

TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)

22C-418

OIL PAN

REMOVAL AND INSTALLATION

M1225028800232

CAUTION

If a fluid leakage is present in the area around the oil pan, clean around the oil pan. After cleaning,
warm up the engine. Only if a fluid leakage is present in the area around the oil pan again, replace the
oil pan assembly.

Pre-removal and Post-installation Operation
Turbocharger By-pass Valve Hose and Charge Air Cooler
Outlet Hose E Removal and Installation (Refer to GROUP 15
− Charge Air Cooler

P.15-12

.)

AC901761AC

2

1

3

10 ± 1 N·m
89 ± 8 in-lb

Removal steps

>>

B

<<

• Transmission Fluid Draining

and Refilling (Refer to

P.22C-399

.)

<<

A

>>

1. Transaxle assembly

connector connection

<<

B

>>

>>

A

<<

2. Oil pan assembly
3. O-ring

Removal steps (Continued)

OIL PAN

TSB Revision

TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)

22C-419

REMOVAL SERVICE POINTS

.

<<A>> TRANSAXLE ASSEMBLY CONNECTOR
DISCONNECTION

Rotate the section A of the connector 90° to the direction of the

arrow to disconnect the connector.

.

<<B>> OIL PAN ASSEMBLY REMOVAL

CAUTION

When removing the oil pan assembly, pay attention to
avoid damage to the connector and the O-ring between the
oil pan assembly and the connector.

AC708151AC

A

OIL PAN

TSB Revision

TWIN CLUTCH- SPORTRONIC SHIFT TRANSMISSION (TC-SST)

22C-420

INSTALLATION SERVICE POINTS

.

>>A<< OIL PAN ASSEMBLY INSTALLATION

1. Completely degrease the oil pan assembly installation

surface on the transaxle side.

2. Remove the gasket from the oil pan assembly, and

completely degrease the groove of the oil pan assembly
(gasket installation area) and the gasket. Then, install the
gasket to the groove of the oil pan assembly.

CAUTION

When installing the oil pan assembly, pay attention to
avoid damage to the connector and the O-ring installed to
the connector.
3. Tighten the screws to the specified torque in the order

shown in the figure.

Tightening torque: 10 ± 1 N⋅ m (89 ± 8 in-lb)

.

>>B<< TRANSMISSION FLUID REFILLING

CAUTION

• If the oil pan assembly and the internal components are

repaired, fill new fluid and check the transmission fluid
level. (Refer to

P.22C-398

.)

• If the oil pan assembly and the internal components are

not repaired, the drained fluid can be reused if it is
between the replacement intervals.

AC807528AC

1

2

3

4

5

6

7

8

9

10

11