Mitsubishi Lancer Evolution X. Manual — part 59
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-261
STEP 54. Using scan tool MB991958, diagnose the CAN
bus line. (checking the A/C-ECU <vehicles with A/C> or
heater control unit <vehicles without A/C> for internal
failure)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect A/C-ECU connector C-22 <vehicles with A/C>
or heater control unit connector C-53 <vehicles without
A/C>.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-262
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between joint connector
(CAN1) C-105 and A/C-ECU connector C-22
<vehicles with A/C> or heater control unit connector
C-53 <vehicles without A/C>.
NO : Check A/C-ECU connector C-22 <vehicles with A/C>
or heater control unit connector C-53 <vehicles
without A/C>, and repair if necessary. If the A/C-ECU
connector <vehicles with A/C> or heater control unit
connector <vehicles without A/C> is in good
condition, replace the A/C-ECU <vehicles with A/C>
or heater control unit <vehicles without A/C>.
AC709542 AD
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
ASC
ENGINE
ETACS
<M/T>
SAS
S-AWC
J/C (1)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
AC709543 AD
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
ASC
LEVER
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
J/C (1)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-263
STEP 55. Using scan tool MB991958, diagnose the CAN
bus line. (checking the radio and CD player or CD changer
for internal failure)
CAUTION
Strictly observe the specified wiring harness repair proce-
dure. For details refer to
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Disconnect radio and CD player or CD changer connector
C-107.
(2) Connect scan tool MB991958 to the data link connector.
(3) Turn the ignition switch to the "ON" position.
AC608435
Data link connector
MB991827
MB991824
MB991910
AB
DIAGNOSIS
TSB Revision
CONTROLLER AREA NETWORK (CAN)
54C-264
(4) Diagnose CAN bus lines, and check if the scan tool
MB991958 screen is as shown in the figure.
OK: The display of the scan tool MB991958 is as
shown in the figure.
Q: Does scan tool MB991958 screen correspond to the
illustration?
YES : Repair the wiring harness between joint connector
(CAN1) C-105 and radio and CD player or CD
changer connector C-107.
NO : Check radio and CD player or CD changer connector
C-107, and repair if necessary. If the radio and CD
player or CD changer connector is in good condition,
replace the radio and CD player or CD changer.
AC709542 AD
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
ASC
ENGINE
ETACS
<M/T>
SAS
S-AWC
J/C (1)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
AC709543 AD
: Red section on screen
M.U.T.
J/C (3)
J/C (2)
ASC
LEVER
ETACS
<TC-SST>
SAS
S-AWC
J/C (4)
TC-SST
ENGINE
J/C (1)
KOS/WCM
SRS
A/C
AUDIO
MMCS
Sat Radio
HFM
OCM
METER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст