Mitsubishi Lancer Evolution X. Manual — part 446
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-849
88 − 89
Intake air temperature sensor 1
13 − 17 kΩ [when intake air temperature is
− 20° C (− 4° F)]
5.4 − 6.6 kΩ [when intake air temperature is 0° C
(32° F)]
2.3 − 3.0 kΩ [when intake air temperature is
20° C (68° F)]
1.0 − 1.5 kΩ [when intake air temperature is
40° C (104° F)]
0.56 − 0.76 kΩ [when intake air temperature is
60° C (140° F)]
0.31 − 0.43 kΩ [when intake air temperature is
80° C (176° F)]
97 − 98
Intake air temperature sensor 2
13 − 18 kΩ [when intake air temperature is
− 20° C (− 4° F)]
5.1 − 6.9 kΩ [when intake air temperature is 0° C
(32° F)]
2.0 − 3.0 kΩ [when intake air temperature is
20° C (68° F)]
0.9 − 1.5 kΩ [when intake air temperature is
40° C (104° F)]
0.40 − 0.78 kΩ [when intake air temperature is
60° C (140° F)]
0.23 − 0.42 kΩ [when intake air temperature is
80° C (176° F)]
TERMINAL
NO.
INSPECTION ITEM
NORMAL CONDITION (INSPECTION
CONDITION)
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-850
INSPECTION PROCEDURE USING AN
OSCILLOSCOPE
M1131154502765
INTAKE CAMSHAFT POSITION SENSOR AND
CRANKSHAFT POSITION SENSOR
Required Special Tools:
• MB991709: Test Harness
• MB992110: Power Plant ECU Check Harness
.
Measurement Method
1. Disconnect the intake camshaft position sensor connector,
and connect the test harness special tool (MB991709)
between the separated connector (All terminals should be
connected).
2. Connect the oscilloscope probe to intake camshaft position
sensor connector terminal No. 3.
3. Disconnect the crankshaft position sensor connector, and
connect the test harness special tool (MB991709) between
the separated connector (All terminals should be
connected).
4. Connect the oscilloscope probe to crankshaft position
sensor connector terminal No. 3.
.
Alternate method
1. Disconnect all ECM connectors. Connect the check harness
special tool (MB992110) between the separated connectors.
AK604465
3
2
1
AD
Intake camshaft position
sensor connector
Oscilloscope
MB991709
AK704086
3
2
1
AB
Crankshaft position
sensor connector
Oscilloscope
MB991709
16 15 14 13 12 11 10 9 8 7 6 5 4 3
2
1
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
AK604467AB
Power plant ECU
check harness connector
MB992110
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-851
2. Connect the oscilloscope to check harness terminal No. 14.
(Check the intake camshaft position sensor signal wave
pattern.)
3. Connect the oscilloscope to check harness terminal No. 8.
(Check the crankshaft position sensor signal wave pattern.)
Standard Wave Pattern
Wave Pattern Observation Points
1. Check that cycle time becomes shorter when the engine
speed increased.
.
AK604468
16 15 14 13 12 11 10 9 8 7 6 5 4 3
2
1
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
Oscilloscope
Power plant ECU
check harness
connector
AB
Observation condition
Function
Special pattern
Pattern height
Low
Pattern selector
Display
Engine r/min
Idle speed
AK703687
AD
2 engine revolutions (1 camshaft revolution)
(Volt)
5
0
5
0
No. 1 TDC
No. 3 TDC
No. 4 TDC
No. 2 TDC
(ms)
Standard wave pattern
Crankshaft position
sensor output wave
pattern
Intake camshaft
position sensor
output wave pattern
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI)
13A-852
Examples of Abnormal Wave Patterns
Example 1
Cause of problem
• Sensor interface malfunction.
Wave pattern characteristics
• Rectangular wave pattern is output even when the
engine is not started.
Example 2
Cause of problem
• Loose timing belt.
• Abnormality in sensor disc.
Wave pattern characteristics
• Wave pattern is displaced to the left or right.
EXHAUST CAMSHAFT POSITION SENSOR AND
CRANKSHAFT POSITION SENSOR
Required Special Tools:
• MB991709: Test Harness
• MB992110: Power Plant ECU Check Harness
.
Measurement Method
1. Disconnect the exhaust camshaft position sensor connector,
and connect the test harness special tool (MB991709)
between the separated connector (All terminals should be
connected).
2. Connect the oscilloscope probe to exhaust camshaft
position sensor connector terminal No. 3.
3. Disconnect the crankshaft position sensor connector, and
connect the test harness special tool (MB991709) between
the separated connector (All terminals should be
connected).
4. Connect the oscilloscope probe to crankshaft position
sensor connector terminal No. 3.
.
AK604469 AB
AK604470
AB
AK604465
3
2
1
AE
Exhaust camshaft position
sensor connector
Oscilloscope
MB991709
AK704086
3
2
1
AB
Crankshaft position
sensor connector
Oscilloscope
MB991709
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст