Mitsubishi Galant. Manual — part 151
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-285
STEP 5. Check connector B-44 at power steering pressure
switch for damage.
Q: Is the connector in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection(
). Then go to Step 14.
STEP 6. Check the power supply voltage at power steering
pressure switch harness side connector B-44.
(1) Disconnect the connector B-44 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.
•
Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the voltage normal?
YES : Go to Step 11.
NO : Go to Step 7.
STEP 7. Check the power supply voltage at PCM connector
C-40 by backprobing
(1) Do not disconnect the PCM connector C-40.
(2) Disconnect the power steering pressure switch connector
B-44.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal 52 and ground by
backprobing.
•
Voltage should be between battery positive voltage.
(5) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the voltage normal?
YES : Go to Step 8.
NO : Go to Step 9.
ACX02520
CONNECTOR : B-44
AF
POWER
STEERING
PRESSURE
SWITCH
AK000260
B-44 HARNESS
SIDE CONNECTOR
1
AC
AK000309
C-40 CONNECTOR
HARNESS SIDE VIEW
46
57
66
45
56
65
44
55
43
49
54
64
42
48
59
41
47
58
53
63
52
62
51
61
50
60
AC
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-286
STEP 8. Check connector C-40 at PCM for damage.
Q: Is the connector in good condition?
YES : Repair harness wire between power steering
pressure switch connector B-44 terminal 1 and PCM
connector C-40 terminal 52 because of open circuit.
Then go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection(
). Then go to Step 14.
STEP 9. Check connector C-40 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection(
). Then go to Step 14.
STEP 10. Check for short circuit to ground between power
steering pressure switch connector B-44 terminal 1 and
PCM connector C-40 terminal 52.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 14.
NO : Repair it. Then go to Step 14.
AK000280
CONNECTOR : C-40
PCM
AV
AK000280
CONNECTOR : C-40
PCM
AV
ACX02520
CONNECTOR : B-44
AF
POWER
STEERING
PRESSURE
SWITCH
AK000280
CONNECTOR : C-40
PCM
AV
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-287
STEP 11. Replace the power steering pressure switch.
(1) Replace the power steering pressure switch.
(2) Check the trouble symptoms.
(3) Check the diagnostic trouble code (DTC).
Q: Is the DTC P0551 is output?
YES : Go to Step 12.
NO : Go to Step 14.
STEP 12. Check connector C-40 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 13.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection(
). Then go to Step 14.
STEP 13. Check for harness damage between power
steering pressure switch connector B-44 terminal 1 and
PCM connector C-40 terminal 52.
Q: Is the harness wire in good condition?
YES : Replace the PCM. Then go to Step 14.
NO : Repair it. Then go to Step 14.
ACX02520
CONNECTOR : B-44
AF
POWER
STEERING
PRESSURE
SWITCH
AK000280
CONNECTOR : C-40
PCM
AV
ACX02520
CONNECTOR : B-44
AF
POWER
STEERING
PRESSURE
SWITCH
AK000280
CONNECTOR : C-40
PCM
AV
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-288
STEP 14. Using scan tool MB991502, check data list item
27: Power Steering Pressure Switch.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK"(OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Start the engine and run at idle.
(3) Set scan tool MB991502 to the data reading mode for item
27, Power Steering Pressure Switch.
•
If the steering wheel is stopped while idling, "OFF" will
be displayed.
•
If the steering wheel is steered while idling, "ON" will be
displayed.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the switch operating properly?
YES : The inspection is complete.
NO : Retry the troubleshooting.
DTC P0705: Transmission Range Sensor Circuit Malfunction (PRNDL Input)
TECHNICAL DESCRIPTION
•
When a malfunction of the park/neutral position
switch is detected, the transaxle control CPU in
the powertrain control module (PCM) outputs a
malfunction signal to the engine control CPU in
the PCM.
DTC SET CONDITIONS
Check Conditions, Judgment Criteria
•
Park/neutral position switch failure signal is input
to the engine control CPU from the transaxle
control CPU.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
•
Park/neutral position switch failed.
•
Open or shorted park/neutral position switch
circuit, or loose connector.
•
PCM failed.
DIAGNOSIS
Required Special Tools
MB991502: Scan Tool (MUT-II)
AC003081 AB
16 PIN
MB991502
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст