Mitsubishi Galant. Manual — part 450
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-267
A/T FA U LTY O PER ATIO N PREVEN TIO N M EC HA N ISM
DIA G NO SIS
INTRODUCTION TO A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS
M1232001600055
If the key interlock and shift lock mechanisms indicates a malfunction, the key interlock cable, the shift lock
cable or the selector lever assembly may be defective. In this case, follow troubleshooting below.
A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS DIAGNOSTIC TROUBLE
SHOOTING STRATEGY
M1232001700041
Use these steps to plan your diagnostic strategy. If
your follow then carefully, you will be sure that you
have exhausted most of the possible ways to find
Automatic Transaxle key interlock and shift lock
mechanisms fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by follows the Symptom
Chart.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1232001800101
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Selector Lever can be Moved from "P" to "R" without Depressing Brake
Pedal when Ignition Key is at Positions Other than "LOCK" (OFF).
TECHNICAL DESCRIPTION (COMMENT)
•
Lock cam or shift lock cable may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of lock cam
•
Malfunction of shift lock cable
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." When the brake pedal is
released with the ignition key at other positions than
"LOCK" (OFF), check that the selector lever can not
be moved from "P" position to "R" position.
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE
PAGE
Selector lever can be moved from "P" to "R" without depressing brake
pedal when ignition key is at position other than "LOCK" (OFF).
1
Selector lever cannot be moved from "P" to "R" with brake pedal
depressed when ignition key is at position other than "LOCK" (OFF).
2
Selector lever can be moved from "P" to "R" with brake pedal depressed
when ignition key is at "LOCK" (OFF) position.
3
Selector lever cannot be moved from "P" to "R" smoothly.
4
Selector lever cannot be moved from "P" to "R".
5
Ignition key cannot be turned to "LOCK" (OFF) position when selector
lever is at "P" position.
6
Ignition key can be turned to "LOCK" (OFF) position when selector lever
is at positions other than "P".
7
-
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-268
INSPECTION PROCEDURE 2: Selector Lever cannot be Moved from "P" to "R"
with Brake Pedal
Depressed when Ignition Key is at Positions Other than "LOCK" (OFF).
TECHNICAL DESCRIPTION (COMMENT)
•
Selector lever assembly, shift lock cable, key
interlock cable, transmission control cable or lock
cam may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of selector lever assembly
•
Malfunction of shift lock cable
•
Malfunction of key interlock cable
•
Malfunction of transmission control cable
•
Malfunction of lock cam
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." When the brake pedal is
depressed with the ignition key at other positions
than "LOCK" (OFF), check that the selector lever can
be moved from "P" position to "R" position.
INSPECTION PROCEDURE 3: Selector Lever can be Moved from "P" to "R" with Brake Pedal
Depressed when Ignition Key is at "LOCK" (OFF) Position.
TECHNICAL DESCRIPTION (COMMENT)
•
Key interlock cable or lock cam may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of lock cam
•
Malfunction of shift lock cable
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." When the brake pedal is
depressed with the ignition key at the "LOCK" (OFF),
check that the selector lever can not be moved from
"P" position to "R" position.
INSPECTION PROCEDURE 4: Selector Lever cannot be Moved from "P" to "R" Smoothly.
TECHNICAL DESCRIPTION (COMMENT)
•
Key interlock cable, shift lock cable, lock cam or
selector lever assembly may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of key interlock cable
•
Malfunction of shift lock cable
•
Malfunction of lock cam
•
Malfunction of selector lever assembly
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." Check that the selector
lever can be moved from "P" position to "R" position
smoothly.
INSPECTION PRICEDURE 5: Selector Lever cannot be Moved from "R" to "P".
TECHNICAL DESCRIPTION (COMMENT)
•
Selector lever assembly or transmission control
cable may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of selector lever assembly
•
Malfunction of transmission control cable
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-269
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." Check that the selector
lever can be moved from "R" position to "P" position.
INSPECTION PROCEDURE 6: Ignition Key cannot be Turned to "LOCK" (OFF) Position when Selector
Lever is at "P" Position.
TECHNICAL DESCRIPTION (COMMENT)
•
Lock cam, key cylinder cover or key interlock
cable may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of lock cam
•
Malfunction of key interlock cable
•
Malfunction of key cylinder slider
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." Check that the ignition key
can not be turned to the "LOCK" (OFF) position with
the selector lever at "P" position.
INSPECTION PROCEDURE 7: Ignition Key can be Turned to "LOCK" (OFF) Position when Selector
Lever is at Positions Other than "P."
TECHNICAL DESCRIPTION (COMMENT)
•
Lock cam, key cylinder cover or key interlock
cable may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of lock cam
•
Malfunction of key cylinder cover
•
Malfunction of key interlock cable
DIAGNOSIS
Check items described in the column
"Troubleshooting Hints." Check that the ignition key
can not be turned to the "LOCK" (OFF) position with
the selector lever at any position other than "P."
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23A-270
SPECIA L TO O LS
M1231000600048
TOOL
TOOL NUMBER AND
NAME
SUPERSES-
SION
APPLICATION
MD998330 (Includes
MD998331) Oil pressure
gauge (2,942 kPa, 427
psi)
MD998330-01
Measurement of hydraulic pressure
MD998332 Adapter
MD998332-01
Connection for oil pressure gauge
MD998478 Test harness
(3 pin, triangle)
MD998478-01
Inspection using an oscilloscope
MB991502 Scan tool
(MUT-II)
MB991496-OD
Checking diagnostic trouble codes
MB991709 Test harness
set
Tool not avail-
able
Inspection using an oscilloscope
MD998900 Adapter
MD998900-01
Connection for oil pressure gauge
MB995062 Flushing tool
−
Flushing cooler and tube
MD998330
MD998332
B991502
MD998900
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст