Mitsubishi Galant. Manual — part 674
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-91
STEP 3. Check wiper motor connector A-02 for damage.
Q: Is wiper motor connector A-02 in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The windshield wiper
should stop at the predetermined park position.
AC03164 AB
CONNECTOR: A-02
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-92
STEP 4. Check the harness wires between wiper motor
connector A-02 and ignition switch (ACC).
NOTE: After checking intermediate connector C-12 and
junction block connectors C-73 and C-84, check the wires. If
intermediate connector C-12 and junction block connectors C-
73 and C-12 are damaged, repair or replace them. Refer to
GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between wiper motor connector
A-02 and ignition switch (ACC) in good condition?
YES : There is no action to be taken.
NO : Repair or replace them. The windshield wiper should
stop at the predetermined park position.
AC03164 AB
CONNECTOR: A-02
AC003131 AB
CONNECTOR: C-12
AC003082AD
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-73
AC003080 AB
JUNCTION BLOCK
(REAR VIEW)
CONNECTOR: C-84
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-93
STEP 5. Check the wiper motor connector A-02 and front-
ECU connector A-09X for damage.
Q: Are wiper motor connector A-02 and front-ECU
connector A-09X in good condition?
YES : Go to Step 6.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
windshield wiper should stop at the predetermined
park position.
AC03164 AB
CONNECTOR: A-02
ACX02500 AD
BATTERY
CONNECTOR: A-09X
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-94
STEP 6. Check the harness wires between wiper motor
connector A-02 and front-ECU connector A-09X.
NOTE: After checking intermediate connector C-05, check the
wires. If intermediate connector C-05 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
.
Q: Is the harness wires between wiper motor connector A-
02 and front-ECU connector A-09X in good condition?
YES : There is no action to be taken.
NO : Repair them. The windshield wiper should stop at the
predetermined park position.
Inspection Procedure F-4: Windshield wiper and washer: Windshield intermittent wiper interval
cannot be adjusted.
TECHNICAL DESCRIPTION (COMMENT).
The ETACS-ECU calculates the intermittent wiper
interval, and sends a signal to the front-ECU through
the SWS communication line.If the signal is
defective, the front-ECU will ignore the signal and set
the intermittent wiper interval to four seconds
TROUBLESHOOTING HINTS
•
Malfunction of speed sensor
•
Malfunction of the column switch (windshield
wiper and washer switch)
•
Malfunction of the ETACS-ECU
•
Malfunction of the front-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991502: Scan Tool (MUT-II)
•
MB991529: Diagnostic Trouble Code Check Harness
AC03164 AB
CONNECTOR: A-02
ACX02500 AD
BATTERY
CONNECTOR: A-09X
AC003089 AC
CONNECTOR: C-05
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст