Mitsubishi Galant. Manual — part 611
AIR BAG MODULE DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-85
WARNING
Store the air bag module on a flat surface with the pad
cover facing up. Do not place anything on top of it.
2. Remove the air bag module from the vehicle. (Refer to
.)
3. Connect two wires, each 6 meters (20 feet) or longer, to the
two leads of special tool MB686560, and cover the
connections with insulation tape. The other ends of the two
wires should be connected to each other (short-circuited), to
prevent sudden unexpected deployment of the air bag
module.
4. Connect the deployment wires to special tool MB686560,
pass it beneath the tire and wheel assembly, and connect it
to the air bag module.
CAUTION
•
Leave some space below the wheel for the deployment
wires. If there is no space, the reaction of the air bag
deployment could result in damage of the adaptor
harness.
•
During deployment, the connector of special tool
MB686560 must not be between the tires.
5. Pass the thick wire through the air bag module mounting
hole, and then secure the air bag module to an old tire with a
wheel in it so that the pad on the module is facing upwards.
6. Place three old tires without wheels on top of the tire
secured to the air bag module, and secure all tires together
with ropes (four locations).
AC001932
CONNECTION
DEPLOYMENT WIRES
MR686560
INSULATOR TAPE
6 m(20 ft)
LONG OR
MORE
AB
ACX01314AB
PASSENGER'S SIDE
AIR BAG MODULE
DEPLOYMENT
WIRES
ACX00611
TIRES WITHOUT
WHEELS
DEPLOYMENT
WIRES
AB
AIR BAG MODULE DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-86
WARNING
•
Before deployment, check carefully to be sure that
no one is nearby.
•
The inflator will be quite hot immediately following
the deployment, so wait at least 30 minutes to
allow it to cool before attempting to handle it.
Although not poisonous, do not inhale gas from
air bag deployment. See Deployed Air Bag Module
Disposal Procedures (Refer to
.) for post-
deployment handling instructions.
•
If the air bag fails to deploy, do not go near the
module. Contact the MMSA Tech Line.
7. At a location as far away from the air bag module as
possible, and from a shielded position, disconnect the two
connected wires from each other, and connect them to the
two terminals of the battery (which has been removed from
the vehicle) to deploy the air bag.
8. Discard the deployed air bag module as specified in
Deployed Air Bag Module Disposal Procedures. (Refer to
.)
DEPLOYMENT OUTSIDE VEHICLE <Side air bag module>
1. Remove the front seatback assembly with side air bag module
from the vehicle. (Refer to
CAUTION
Once disconnected, both electrodes of the side air bag module
connector short automatically to prevent accidental deployment
caused by static etc. Still, in consideration of the accidental
deployment, store the air bag module on flat place with
deployment surface facing up. Also, do not put anything on it.
. 2. Connect two wires, each 6 meters (20 feet) or longer, to the two
leads of special tool MB686560, and cover the connections with
insulation tape. The other ends of the two wires should be
connected to each other (short-circuited), to prevent sudden
unexpected deployment of the air bag module.
3. Place the front seat back assembly with its back contact with
the ground.
4. Connect the SRS air bag adapter harness with the
deployment wires to the side air bag module connector.
ACX01315
DEPLOYMENT WIRES
AB
AC001932
CONNECTION
DEPLOYMENT WIRES
MR686560
INSULATOR TAPE
6 m(20 ft)
LONG OR
MORE
AB
ACX00612AB
SRS AIR BAG ADAPTER
HARNESS MB686560
FRONT SEAT
BACK ASSEMBLY
AIR BAG MODULE DISPOSAL PROCEDURES
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-87
CAUTION
•
Before the deployment, see that no one is near the front
seatback assembly.
•
The deployment makes the inflator of the side air bag
very hot. Before handling the inflator, wait more than 30
minutes for cooling.
•
If the side air bag module fails to deploy although the
procedure is respected, do not go near the module.
Contact the MMSA Tech Line.
5. Disconnect the deployment wires as far from the front seat
back assembly possible and connect the harnesses to the
battery removes from the vehicle. Then, deploy.
6. Remove the deployed air bag module from the seat back
assembly and discard as specified in the procedure.
DEPLOYED AIR BAG MODULE DISPOSAL
After deployment, the air bag module should be disposed of in
the same manner as any other scrap parts, adhering to local
laws and/or legislation. Observe the following precautions
during air bag disposal:
1. The inflator will be quite hot immediately following
deployment, so wait at least 30 minutes to allow it cool
before attempting to handle it.
2. Do not put water or oil on the air bag after deployment.
WARNING
If after following these precautions, any material does
get into the eyes or on the skin, immediately rinse the
affected area with a large amount of clean water. If
any irritation develops, seek medical attention.
3. There may be material on the deployed air bag module, that
could irritate the eye and/or skin. Wear gloves and safety
glasses when handling a deployed air bag module.
4. Tightly seal the air bag module in a strong plastic bag for
disposal.
5. Be sure to always wash your hands after completing this
operation.
ACX01316
DEPLOYMENT
WIRES
AB
ACX00613AB
STRONG
VINYL BAG
AIR BAG
MODULE
SPECIFICATIONS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-88
SPECIFIC ATIO NS
SPECIFICATIONS
M1524004900084
FASTENER TIGHTENING SPECIFICATIONS
SERVICE SPECIFICATIONS
M1524000400076
ITEMS
SPECIFICATIONS
Air bag module (driver's side) mounting screw
9.0
±
2.0 N
⋅
m (78
±
17 in-lb)
Side impact sensor and bracket nut
4.9
±
1.0 N
⋅
m (44
±
8 in-lb)
Side impact sensor bracket bolt
4.9
±
1.0 N
⋅
m (44
±
8 in-lb)
SRS-ECU mounting bolt
4.9
±
1.0 N
⋅
m (44
±
8 in-lb)
SRS-ECU bracket bolt
4.9
±
1.0 N
⋅
m (44
±
8 in-lb)
Steering wheel nut
41
±
8 N
⋅
m (31
±
5 ft-lb)
ITEMS
STANDARD VALUE
Clock spring resistance
Ω
less than 0.4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст