Mitsubishi Galant. Manual — part 484
SPECIFICATIONS
TSB Revision
FRONT AXLE
26-25
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1261005400053
GENERAL SPECIFICATIONS
M1261000200054
SERVICE SPECIFICATIONS
M1261000300051
LUBRICANTS
M1261000400058
ITEMS
SPECIFICATIONS
Driveshaft
Center bearing bolt
40 N
⋅
m (30 ft-lb)
Driveshaft nut
196
−
255 N
⋅
m (145
−
188 ft-lb)
Lower arm ball joint nut
98
−
118 N
⋅
m (72
−
81 ft-lb)
Stabilizer link nut
44 N
⋅
m (32 ft-lb)
Tie rod end nut
24
−
33 N
⋅
m (17
−
25 ft-lb)
Front hub assembly
Caliper assembly bolt
90
−
110 N
⋅
m (66
−
81 ft-lb)
Driveshaft nut
196
−
255 N
⋅
m (145
−
188 ft-lb)
Knuckle and wheel bearing bolt
88 N
⋅
m (65 ft-lb)
Lower arm ball joint nut
98
−
118 N
⋅
m (72
−
81 ft-lb)
Stabilizer link nut
44 N
⋅
m (32 ft-lb)
Tie rod end nut
24
−
33 N
⋅
m (17
−
25 ft-lb)
Knuckle
Dust shield bolt
9 N
⋅
m (78 in-lb)
Front strut nut
275
−
324 N
⋅
m (203
−
239 ft-lb)
ITEMS
SPECIFICATIONS
Front axle hub bearing
Type
Double row angular contact bearing
Driveshaft
Joint type
Outer
Birfield joint
Inner
Tripod joint
ITEMS
STANDARD VALUE
LIMIT
Front axle total backlash mm (in)
-
0.05 (0.002)
Setting of boot length mm (in)
85
±
3 (3.3
±
0.12)
-
Wheel bearing breakaway torque N
⋅
m (in-lb)
-
1.0 (9)
ITEMS
SPECIFIED LUBRICANTS
QUANTITY
Dust seal inner
Repair kit grease
14
−
20 g (0.5
−
0.7 oz)
Dust seal outer
Repair kit grease
8
−
12 g (0.3
−
0.4 oz)
TJ boot grease
2.4L ENGINE
Repair kit grease
100
±
10 g (3.5
±
0.4 oz)
3.0L ENGINE
Repair kit grease
105
±
10 g (3.7
±
0.4 oz)
BJ boot grease
2.4L ENGINE
Repair kit grease
110
±
10 g (3.9
±
0.4 oz)
3.0L ENGINE
Repair kit grease
120g (4.2 oz)
NOTES
27-1
GROUP 27
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
REAR AXLE DIAGNOSIS . . . . . . . . .
INTRODUCTION TO REAR AXLE
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . .
REAR AXLE DIAGNOSTIC
TROUBLESHOOTING STRATEGY . . . . . .
SYMPTOM CHART. . . . . . . . . . . . . . . . . . .
SYMPTOM PROCEDURES . . . . . . . . . . . .
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
WHEEL BEARING END PLAY CHECK . . .
REAR HUB ROTARY-SLIDING
RESISTANCE CHECK . . . . . . . . . . . . . . . .
HUB BOLT REPLACEMENT. . . . . . . . . . . .
REAR AXLE HUB ASSEMBLY . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
KNUCKLE . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
REAR AXLE
27-2
.
G EN ER A L DESC RIPTIO N
M1271000100047
The rear axle consists of a knuckle, rear hub, unit
bearing. The unit bearing is press-fitted to the rear
hub and bolted to the knuckle. Also, the unit bearing
utilizes the same type of double row angular contact
ball bearing as does the front axle.
ABS rotor for detecting the vehicle speed is located
on the hub assembly, and a speed sensor is located
on the knuckle.
R EA R A XLE D IA G N O SIS
INTRODUCTION TO REAR AXLE DIAGNOSIS
M1271004100049
Noise from the rear axle may be caused by defects in
the components.
REAR AXLE DIAGNOSTIC TROBLESHOOTING STRATEGY
M1271004200046
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
rear axle fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Inspection
Chart for Trouble Symptoms.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1271004300043
AC001179 AD
KNUCKLE
CAP
<VEHICLES WITHOUT ABS>
ABS ROTOR
<VEHICLES WITH ABS>
OIL SEAL
OIL SEAL
UNIT BEARING
REAR HUB
SYMPTOM
INSPECTION PROCEDURE
REFERENCE PAGE
Abnormal noise
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст