Mitsubishi Galant. Manual — part 716
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-259
Inspection Procedure N-15: Column switch: The windshield mist wiper switch, windshield
intermittent wiper switch, windshield low-speed wiper switch, windshield high-speed wiper switch or
windshield washer switch signal is not sent to the ETACS-ECU.
CIRCUIT OPERATION
The ETACS-ECU uses the input signal from the
column switch (windshield wiper and washer switch)
to operate various functions.
TECHNICAL DESCRIPTION (COMMENT)
The column switch (windshield wiper and washer
switch) input signal is used to operate the windshield
wiper and washer. If the signal fails, windshield wiper
and washer will not work normally.
TROUBLESHOOTING HINTS
•
Malfunction of the column switch (windshield
wiper and washer switch)
•
Malfunction of the ETACS-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Test Harness Set
STEP 1. Check the ignition switch positions.
Q: Does a diagnostic trouble code set when the ignition
switch is at any of the positions?
YES : Carry out the troubleshooting by referring to the
Diagnostic Trouble Code Chart. Refer to
NO : Go to Step 2.
AC004263
Windshield Wiper and Windshield Washer Switch Input Circuit
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-260
STEP 2. Check the windshield wiper and washer switch.
Q: Is the windshield wiper and washer switch in good
condition?
YES : Go to Step 3.
NO : Replace it. The input signal from the column switch
(windshield wiper and washer switch) should be able
to be checked and the windshield wiper and washer
should work normally.
STEP 3. Replacement of ECU
(1)Replace the column switch (turn-signal light and lighting
switch).
(2)The input signal from the column switch (windshield wiper
and washer switch) should be able to be checked and the
windshield wiper and washer should work normally.
Q: Is the input signal from the column switch (windshield
wiper and washer switch) input normally?
YES : There is no action to be taken.
NO : Replace the ETACS-ECU. The input signal from the
column switch (windshield wiper and washer switch)
should be able to be checked and the windshield
wiper and washer should work normally.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
−
No continuity
Windshield mist
wiper switch
22
−
32
Continuity
Windshield
intermittent wiper
switch
22
−
31
Continuity
Windshield
low-speed wiper
switch
22
−
30
Continuity
Windshield
high-speed wiper
switch
21
−
23
Continuity
Windshield
washer switch
22
−
23
Continuity
AC003178
UPPER SIDE
AB
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-261
Inspection Procedure N-16: The windshield intermittent wiper interval adjusting knob signal is not
sent to the ETACS-ECU.
CIRCUIT OPERATION
The ETACS-ECU calculates the windshield
intermittent wiper interval according to the resistance
of the windshield intermittent wiper interval adjusting
knob, which is incorporated in the column switch
(windshield wiper and windshield washer switch).
TECHNICAL DESCRIPTION (COMMENT)
If the windshield intermittent wiper interval adjusting
knob is defective, the windshield intermittent wiper
interval can not be adjusted.
TROUBLESHOOTING HINTS
•
Malfunction of the column switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Test Harness Set
Windshield Intermittent Wiper Intervals Adjusting Knob Input Circuit
AC004264
AC003078 AB
CONNECTOR: C-60
COLUMN SWITCH
AC003082AC
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-82
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-262
STEP 1. Check the windshield intermittent wiper interval
adjusting knob and column switch body.
Check the resistance at terminal numbers 27 and 28. The
resistance should change smoothly from approximately 0
Ω
("FAST" position) to approximately 1 k
Ω
("SLOW" position).
Q: Is the windshield intermittent wiper interval adjusting
knob in good condition?
YES : Go to Step 2.
NO : Replace the it. Check that the input signal from the
windshield intermittent wiper interval adjusting knob
can be checked and the wiper interval can be
adjusted.
STEP 2. Check column switch connector C-60 and ETACS-
ECU connector C-82 for damage.
Q: Is column switch connector C-60 and ETACS-ECU
connector C-82 in good condition?
YES : Go to Step 3.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
. Check that
the input signal from the windshield intermittent wiper
interval adjusting knob can be checked and the wiper
interval can be adjusted.
AC003178
UPPER SIDE
AB
AC003078 AB
CONNECTOR: C-60
COLUMN SWITCH
AC003082AC
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-82
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст