Mitsubishi Galant. Manual — part 360
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-10
INSPECTION USING SCAN TOOL MB991502,
DATA LIST
Required Special Tool:
•
MB991502: Scan Tool (MUT-II)
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
1. Connect scan tool MB991502 to the data link connector.
2. Turn the ignition switch to "ON" position.
3. Carry out inspection by means of the data list.
If there is an abnormality, check and repair the chassis
harnesses and components. (Refer to
, Data List
Reference Table.)
4. Re-check using scan tool MB991502 and check to be sure
that the abnormal input and output have returned to normal
because of the repairs.
5. Erase the diagnostic trouble code(s).
6. Turn the ignition switch to "LOCK" (OFF) position.
7. Disconnect scan tool MB991502 from the data link
connector.
8. Start the engine again and do a test drive to confirm that the
problem is eliminated.
DIAGNOSTIC TROUBLE CODE CHART
M1172002200057
Check according to the inspection chart that is
appropriate for the diagnostic trouble code.
AC004569
MB991502
16 PIN
AB
DIAGNOSTIC TROUBLE
CODE NO.
INSPECTION ITEM
REFERENCE PAGE
11
Auto-cruise vacuum pump drive system
12
Vehicle speed sensor system
14
Stoplight switch system
15
Auto-cruise control switch system
16
Auto-cruise control-ECU system
17
Throttle position sensor system
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-11
DIAGNOSTIC TROBLE CODE PROCEDURES
DTC 11: Auto-cruise Vacuum Pump Drive System
AC004570
Auto-cruise Vacuum Pump Drive System Circuit
AB
AC001449
CONNECTOR: A-01
RESERVE
TANK
AB
AC004571
CONNECTOR: C-05
COMBINATION METER
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-12
CIRCUIT OPERATION
This circuit activates the vacuum pump used to
accelerate/decelerate, set, and cancel the vehicle
speed.
The auto-cruise control-ECU controls the control
valve, release valve, and motor by turning the
transistor in the ECU on and off.
DTC SET CONDITIONS
Any drive signal for the release valve, control valve
or motor is not input to the auto-cruise control-ECU.
TROUBLESHOOTING HINTS
The most likely causes for this code to be set are:
•
Malfunction of the auto-cruise vacuum pump.
•
Damaged harness or connector.
•
Malfunction of the auto-cruise control-ECU.
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
STEP 1. Check the output circuit voltage at auto-cruise
control-ECU connector C-52 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-52.
(2) Turn the ignition switch to "ON" position and the auto-cruise
control main switch to "ON" position.
(3) Measure the voltage between terminal 7 and ground by
backprobing.
•
Voltage should be battery positive voltage.
[When decelerating with the "SET" switch while driving
at constant speed (Release valve open).]
(4) Measure the voltage between terminal 8 and ground by
backprobing.
•
Voltage should be battery positive voltage.
[When decelerating with the "SET" switch while driving
at constant speed. (Control valve open).]
(5) Measure the voltage between terminal 16 and ground by
backprobing.
•
Voltage should be battery positive voltage.
(When the motor is stopped during a constant road
speed.)
(6) Turn the ignition switch to "LOCK" (OFF) position.
Q: Are all of the above values satisfied?
YES : Check that diagnostic trouble code 11 is not output.
If diagnostic trouble code 11 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 11 is not.
NO : Go to Step 2.
AC004573AC
GLOVE BOX
CONNECTOR: C-12
AC004572AB
CONNECTOR: C-52
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
ACX01897
C-52 CONNECTOR
HARNESS SIDE VIEW
AD
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-13
STEP 2. Check auto-cruise control-ECU connector C-52
and intermediate connector C-12.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 11 is not
output.
NO : Go to Step 3.
STEP 3. Check auto-cruise control vacuum pump
connector A-01.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E Harness Connector Inspection
.
Then check that diagnostic trouble code 11 is not
output.
NO : Go to Step 4.
AC004572AB
CONNECTOR: C-52
AC004573AC
GLOVE BOX
CONNECTOR: C-12
AC001449
CONNECTOR: A-01
RESERVE
TANK
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст