Mitsubishi Galant. Manual — part 373
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-62
INSPECTION PROCEDURE 7: Auto-cruise Control Indicator Light inside Combination Meter does not
Illuminate. (However, Auto-cruise Control is Normal.)
AC004599
Auto-cruise Control Indicator Light Drive Circuit
AB
AC004600
CONNECTORS: C-29, C-30
AB
C-29
C-30
AC004572AB
CONNECTOR: C-52
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-63
CIRCUIT OPERATION
The power for the auto-cruise indicator in the
combination meter is supplied from the ignition
switch (IG1).
When the auto-cruise control system is operating,
the transistor inside the auto-cruise control-ECU
illuminates the auto-cruise indicator through ECU
terminal number 15.
TECHNICAL DESCRIPTION (COMMENT)
The cause is probably the malfunction of the
indicator bulb or the malfunction of the connector or
harness.
TROUBLESHOOTING HINTS
•
Malfunction of the indicator bulb.
•
Damaged harness or connector.
•
Malfunction of the auto-cruise control-ECU.
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
STEP 1. Check the auto-cruise control indicator bulb.
(1) Remove the combination meter.
Refer to GROUP 54A, Combination Meter Assembly and
Vehicle Speed Sensor
.
(2) Check the auto-cruise control indicator bulb.
Q: Is the bulb blown?
YES : Replace the bulb.
Then check that the malfunction is eliminated.
NO : Go to Step 2.
AC004592AB
CONNECTOR: C-73
JUNCTION BLOCK
(FRONT VIEW)
AC004601AB
CONNECTOR: C-78
JUNCTION BLOCK
(FRONT VIEW)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-64
STEP 2. Check the output circuit voltage at auto-cruise
control-ECU connector C-52 by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-52.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 15 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Check that the malfunction is eliminated.
If the malfunction is eliminated, replace the auto-
cruise control-ECU. (Refer to
.)
Then check that the malfunction is eliminated.
NO : Go to Step 3.
STEP 3. Check the output circuit voltage at junction block
connector C-78 by backprobing.
(1) Do not disconnect junction block connector C-78.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 6 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 5.
NO : Go to Step 4.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
AC002355
C-52 CONNECTOR
HARNESS SIDE VIEW
AC
AC002391
1 2 3 4
5 6 7 8 9
10 1112 1314 15 16 1718 19 20
C-78 CONNECTOR
HARNESS SIDE VIEW
AC
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-65
STEP 4. Check junction block connector C-73.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Replace the junction block.
Then check that the malfunction is eliminated.
STEP 5. Check combination meter connector C-29 and C-
30.
Q: Is any connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Go to Step 6.
STEP 6. Check the harness wire between combination
meter connector C-29 and junction block connector C-78.
Q: Is any harness wire between combination meter
connector C-29 and junction block connector C-78
damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Go to Step 7.
AC004592AB
CONNECTOR: C-73
JUNCTION BLOCK
(FRONT VIEW)
AC004600
CONNECTORS: C-29, C-30
AB
C-29
C-30
AC004602
CONNECTOR: C-29
AB
AC004601AB
CONNECTOR: C-78
JUNCTION BLOCK
(FRONT VIEW)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст