Mitsubishi Galant. Manual — part 428
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-179
STEP 3. Check the solenoid valve output voltage at PCM
connector C-42 by backprobing.
(1) Do not disconnect connector C-42.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 130 and ground by
backprobing.
•
Voltage should be battery positive voltage.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 4.
NO : Go to Step 9.
STEP 4. Check connectors B-38 at solenoid valve
assembly and C-42 at PCM for damage.
Q: Are the connectors in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC004197
PCM
AF
CONNECTOR: C-42
AC001965
C-42 CONNECTOR
HARNESS SIDE VIEW
AE
ACX02479
CONNECTOR: B-38
AF
AC004197
PCM
AF
CONNECTOR: C-42
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-180
STEP 5. Check harness for damage between solenoid
valve assembly connector B-38 terminal 5 and PCM
connector C-42 terminal 130.
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it.
STEP 6. Check connector A-19X at A/T control relay for
damage.
Q: Is the connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
ACX02479
CONNECTOR: B-38
AF
AC004197
PCM
AF
CONNECTOR: C-42
AC004286 AC
A/T CONTROL
RELAY
BATTERY
CONNECTOR: A-19X
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-181
STEP 7. Check harness for damage between solenoid
valve assembly connector B-38 terminal 9 and A/T control
relay connector A-19X terminal 3.
Q: Is the harness wire in good condition?
YES : Go to Step 8.
NO : Repair it.
STEP 8. Using scan tool MB991502, check actuator test
item 04: Overdrive Solenoid Valve.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Set scan tool MB991502 to the actuator test mode for item
04: Overdrive Solenoid Valve.
•
An operation sound should be heard from solenoid
valve when the overdrive solenoid valve is operated.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : This malfunction is intermittent. Refer to GROUP 00,
How to Use Troubleshooting/Inspection Service
Points
−
How to Cope with Intermittent Malfunction
NO : Replace the PCM.
ACX02479
CONNECTOR: B-38
AF
AC004286 AC
A/T CONTROL
RELAY
BATTERY
CONNECTOR: A-19X
AC003081AC
MB991502
DATA LINK
CONNECTOR
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-182
STEP 9. Check connector B-38 at solenoid valve assembly
for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 10. Check the overdrive solenoid valve at solenoid
valve assembly connector B-38.
(1) Disconnect connector B-38 and measure at the solenoid
valve side.
(2) Measure the resistance between terminal 5 and 9.
Standard value: 2.7
−−−−
3.4
Ω
Ω
Ω
Ω
Q: Is the resistance at the standard value?
YES : Go to Step 11.
NO : Replace the overdrive solenoid valve. Refer to
GROUP 23B, Valve Body
.
ACX02479
CONNECTOR: B-38
AF
ACX02479
CONNECTOR: B-38
AF
AC001968
HARNESS
CONNECTOR: B-38
AE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст