Mitsubishi Galant. Manual — part 593
INTRODUCTION
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-13
AC002972
INTRODUCTION
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-14
COMPONENT LOCATION
AC003193AB
DATA LINK CONNECTOR
SIDE IMPACT SENSOR
SIDE IMPACT
SENSOR
CENTER
PILLAR
FRONT
OF
VEHICLE
SRS-ECU
SERVICE PRECAUTIONS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-15
SERVIC E PR ECA UTIO NS
M1524000300080
WARNING
•
In order to avoid injury to yourself or others from
accidental deployment of the air bag during
servicing, read and carefully follow all the
precautions and procedures described in this
manual.
•
After disconnecting the battery cable, wait 60
seconds or more before proceeding with the
following work. The SRS system is designed to
retain enough voltage to deploy the air bag for a
short time even after the battery has been
disconnected, so serious injury may result from
unintended air bag deployment if work is done on
the SRS system immediately after the battery
cables are disconnected.
•
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
•
Do not use any electrical test equipment on or near
the SRS components, except those specified on
•
Never Attempt to Repair the Following
Components: SRS-ECU, Clock Spring, Air Bag
Module, Side Impact Sensor. If any of these
components are diagnosed as faulty, they should
only be replaced, in accordance with the
INDIVIDUAL COMPONENT SERVICE procedures in
this manual, starting on page
•
Do not attempt to repair the wiring harness
connectors of the SRS. If any of the connectors are
diagnosed as faulty, replace the wiring harness. If
the wires are diagnosed as faulty, replace or repair
the wiring harness according to the following
table.
ACX00583
INSULATING TAPE
BATTERY
BATTERY CABLE (–)
AC
AC002967AB
SRS-ECU CONNECTOR
<VEHICLES WITHOUT SRS SIDE AIR BAG>
<VEHICLES WITH SRS SIDE AIR BAG>
SRS-ECU TERMINAL
NO.
DESTINATION OF HARNESS
CORRECTIVE ACTION
3
Body wiring harness
→
Ground
Correct or replace the body wiring
harness.
4
Body wiring harness
→
Instrument
panel wiring
→
SRS warning light
Correct or replace each wiring harness.
5, 6
Body wiring harness
→
Air bag module
(Front passenger's side)
Correct or replace the body wiring
harness.
SERVICE PRECAUTIONS
TSB Revision
SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
52B-16
NOTE: *Vehicles with side air bags
WARNING
•
Inspection of the SRS-ECU connector harness
should be carried out by the following procedure.
Insert the backprobing tool into connector from
harness side, and connect the tester to
backprobing tool. If any tool other than
backprobing tool is used, it may cause damage to
the harness and other components. Furthermore,
measurement should not be carried out by
touching the backprobing tool directly against the
terminals from the front of the connector. The
terminals are plated to increase their conductivity,
so if they are touched directly by the backprobing
tool, the plating may break, which will decrease
reliability.
•
The SRS components should not be subjected to
heat over 93
°°°°
C(200
°°°°
F
),),),),
so remove the SRS-ECU, air
bag module, and clock spring before drying or
baking the vehicle after painting.
•
After servicing the SRS system, check the warning
light operation to make sure that the system
functions properly. (Refer to
•
Make certain that the ignition switch is
"LOCK"(OFF) position when the scan tool is
connected or disconnected.
•
If you have any questions about the SRS system,
please contact the MMSA Tech Line.
7, 8
Body wiring harness
→
Clock spring
→
Air bag module (Driver's side)
Correct or replace each wiring harness.
Replace the clock spring.
9
Body wiring harness
→
Junction block
(fuse No.5)
Correct or replace the body wiring
harness.
12
Body wiring harness
→
Junction block
(fuse No.13)
Correct or replace the body wiring
harness.
16
Body wiring harness
→
Data link
connector
Correct or replace the body wiring
harness.
21*, 22*
Body wiring harness
→
Side air bag
module (LH)
Correct or replace the body wiring
harness.
23*, 24*
Body wiring harness
→
Side air bag
module (RH)
Correct or replace the body wiring
harness.
34*, 35*, 36*
Body wiring harness
→
Floor wiring
harness
→
Side impact sensor (LH)
Correct or replace each wiring harness.
40*, 41*, 42*
Body wiring harness
→
Floor wiring
harness
→
Side impact sensor (RH)
Correct or replace each wiring harness.
SRS-ECU TERMINAL
NO.
DESTINATION OF HARNESS
CORRECTIVE ACTION
AC003072
SRS-HARNESS CONNECTOR
SRS-ECU HARNESS CONNECTOR
(REAR SIDE)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст