Mitsubishi Galant. Manual — part 6
VEHICLE IDENTIFICATION
TSB Revision
GENERAL <BODY AND CHASSIS>
00-21
LOCATIONS
THEFT PROTECTION LABEL TARGET AREA (A: FOR ORIGINAL EQUIPMENT PARTS, B: FOR RE-
PLACEMENT PARTS)
AC000058
ENGINE
<4G64>
AB
A
B
AC000061
ENGINE
<6G72>
AB
B
A
AC000060
AUTOMATIC TRANSAXLE
AB
A
B
AC004807
FENDER
B
A
AB
THE ILLUSTRATION INDICATES LEFT OUTER SIDE
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
AC004808
QUARTER PANEL OUTER
THE ILLUSTRATION INDICATES LEFT OUTER SIDE.
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
A
B
AB
AC004809 AB
FRONT DOOR
A
B
THE ILLUSTRATION INDICATES LEFT OUTER SIDE.
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-22
PR ECA U TIO N S BEFO R E SERVIC E
M1001000500107
SUPPLEMENTAL RESTRAINT SYSTEM
(SRS)
1. Items to follow when servicing SRS are the
followings:
(1) Be sure to read GROUP 52B, Supplemental
Restraint System (SRS). For safe operation,
please follow the directions and heed all
warnings.
THEFT PROTECTION LABEL TARGET AREA (A: FOR ORIGINAL EQUIPMENT PARTS, B: FOR RE-
PLACEMENT PARTS)
AC004810 AB
Rear door
A
B
THE ILLUSTRATION INDICATES LEFT OUTER SIDE.
RIGHT SIDE IS SYMMETRICALLY OPPOSITE.
AC004811 AB
A
B
HOOD
AC004812 AB
B
TRUNK LID
A
AC004813 AB
A
B
FRONT BUMPER
AC004826 AB
REAR BUMPER
A
B
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-23
(2) Wait at least 60 seconds after disconnecting
the battery cable before doing any further
work. The SRS system is designed to retain
enough voltage to deploy the air bag even
after the battery has been disconnected.
Serious injury may result from unintended air
bag deployment if work is done on the SRS
system immediately after the battery cable is
disconnected.
(3) Warning labels must be heeded when
servicing or handling SRS components.
NOTE: Warning labels can be found in the
following locations:
.
•
Sun visor
•
Glove box
•
SRS-ECU
•
Air bag module (Driver's side or
passenger's side)
•
Side air bag module
•
Clock spring
•
Steering gear box
•
Side impact sensor
(4) Always use the designated special tools and
test equipment.
(5) Store components removed from the SRS in a
clean and dry place. The air bag module
should be stored on a flat surface and placed
so that the pad surface is facing upward.
(6) Never attempt to disassemble or repair the
SRS components (SRS-ECU, air bag module,
clock spring, and side impact sensor). If there
is a defect, replace the defective part.
(7) Whenever you finish servicing the SRS, check
the SRS warning light operation to make sure
that the system functions properly.
(8) Be sure to deploy the air bag before disposing
of the air bag module or disposing of a vehicle
equipped with an air bag. (Refer to GROUP
52B, Air Bag Module Disposal
Procedures
.)
2. Observe the following when carrying out
operations on places where SRS components are
installed, including operations not directly related
to the SRS air bag.
(1) When removing or installing parts, do not
allow any impact or shock to the SRS
components.
(2) SRS components should not be subjected to
temperatures of over 93
°
C (200
°
F), so remove
the SRS components before drying or baking
the vehicle after painting. After re-installing
them, check the SRS warning light operation
to make sure that the system functions
properly.
SERVICING ELECTRICAL SYSTEM
WARNING
Battery posts, terminals and related accessories
contain lead and lead compounds. WASH HANDS
AFTER HANDLING.
1. Note the following before proceeding with working on the
electrical system.
Never perform unauthorized modifications to any electrical
device or wiring. Such modifications might lead to a vehicle
malfunction, over-capacity or short-circuit that could result in
a fire in the vehicle.
ACX00880AB
PRECAUTIONS BEFORE SERVICE
TSB Revision
GENERAL <BODY AND CHASSIS>
00-24
CAUTION
•
Before connecting or disconnecting the negative
battery cable, be sure to turn off the ignition switch and
the lights. (If this is not done, there is the possibility of
semiconductor parts being damaged.)
•
After completion of the work steps (when the negative
battery terminal is connected), warm up the engine and
allow it to idle for approximately 10 minutes under the
conditions described below in order to stabilize engine
control conditions, and then check to be sure that the
idling is satisfactory.
2. When servicing the electrical system, disconnect the
negative cable terminal from the battery.
Engine coolant temperature: 80
°°°°
−−−−
95
°°°°
C (176
°°°°
−−−−
203
°°°°
F)
Lights and all accessories: OFF
Transaxle: N or P position
Steering wheel: straight-forward position
VEHICLE WASHING
If high-pressure car-washing equipment or steam car-washing
equipment is used to wash the vehicle, be sure to maintain the
spray nozzle at a distance of at least approximately 40cm (16
inches) from any plastic parts and all opening parts (doors,
luggage compartment, etc.).
APPLYING ANTI-CORROSION AGENT OR OTHER
UNDERCOAT AGENTS
Be careful not to adhere oil or grease to the heated oxygen
sensor. If adhered, the sensor may malfunction. Protect the
heated oxygen sensor with a cover before applying anti-
corrosion agent, etc.
SCAN TOOL (MUT-II)
CAUTION
Turn the ignition switch to "LOCK" (OFF) position before
disconnecting or connecting the scan tool.
To operate the scan tool, refer to "MUT-II Operating
Instructions."
ACX00881AB
APPROXIMATELY
40 cm (16 in)
ACX00882 AB
SCAN TOOL (MUT-II)
ROM PACK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст