Mitsubishi Galant. Manual — part 54
11C-1
GROUP 11C
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
ENGINE DIAGNOSIS. . . . . . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON VEHICLE SERVICE . . . . . . . . . . .
DRIVE BELT TENSION CHECK AND ADJUSTMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION TIMING CHECK . . . . . . . . . . . . .
IDLE MIXTURE CHECK . . . . . . . . . . . . . . .
CURB IDLE SPEED CHECK . . . . . . . . . . .
COMPRESSION PRESSURE CHECK. . . .
MANIFOLD VACUUM CHECK . . . . . . . . . .
LASH ADJUSTER CHECK . . . . . . . . . . . . .
ENGINE ASSEMBLY . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
CAMSHAFT AND CAMSHAFT OIL SEAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
OIL PAN . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
CRANKSHAFT FRONT OIL SEAL. . .
REMOVAL AND INSTALLATION . . . . . . . .
CRANKSHAFT REAR OIL SEAL. . . .
REMOVAL AND INSTALLATION . . . . . . . .
CYLINDER HEAD GASKET . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
TIMING BELT . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING SPECIFICATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-2
.
G EN ER A L DESC RIPTIO N
M1111000100107
The 6G72 (3.0L) engine is a six-cylinder engine. The cylinder numbers are assigned as 1-3-5 for the right
bank and 2-4-6 for the left bank from the front of the engine (timing belt side). This engine is fired in the order
of the 1, 2, 3, 4, 5 and 6 cylinders.
EN G IN E D IA G N O SIS
M1111000700080
ITEMS
SPECIFICATIONS
Type
V-type, overhead camshaft
Number of cylinders
6
Bore mm (in)
91.1 (3.59)
Stroke mm (in)
76.0 (2.99)
Piston displacement cm
3
(cu in)
2,972 (181.4)
Compression ratio
9.0
Firing order
1-2-3-4-5-6
Valve timing
Intake valve
Opens (BTDC)
15
°
Closes (ABDC)
53
°
Exhaust valve
Opens (BBDC)
53
°
Closes (ATDC)
15
°
SYMPTOMS
PROBABLE CAUSE
REMEDY
Compression is too
low
Blown cylinder head gasket
Replace the gasket.
Worn or damaged piston rings
Replace the rings.
Worn piston or cylinder
Repair or replace the piston and/or the
cylinder block.
Worn or damaged valve seat
Repair or replace the valve and/or the
seat ring
Drop in oil pressure
Engine oil level is too low
Check the engine oil level.
Malfunction of oil pressure switch
Replace the oil pressure switch.
Clogged oil filter
Install a new filter.
Worn oil pump gears or cover
Replace the gears and/or the cover.
Thin or diluted engine oil
Change the engine oil to the correct
viscosity.
Stuck (opened) oil relief valve
Repair the relief valve.
Excessive bearing clearance
Replace the bearings.
Oil pressure too high
Stuck (closed) oil relief valve
Repair the relief valve.
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-3
SPECIA L TO O LS
M1111000600124
Noisy valves
Malfunction of lash adjuster (including
entry of air into high pressure chamber)
Check the lash adjuster.
Thin or diluted engine oil (low oil
pressure)
Change the engine oil.
Worn or damaged valve stem or valve
guide
Replace the valve and/or the guide.
Connecting rod noise/
main bearing noise
Insufficient oil supply
Check the engine oil level.
Thin or diluted engine oil
Change the engine oil.
Excessive bearing clearance
Replace the bearings.
SYMPTOMS
PROBABLE CAUSE
REMEDY
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991502
Scan tool (MUT-II)
MB991496-OD
•
Ignition timing check
•
Idle speed check
MB991453
Engine hanger assembly
MZ203827-01
Supporting the engine
assembly during remove
and installation of the tran-
saxle
GENERAL SERVICE
TOOL
MZ203827
Engine lifter
MZ203827-01
MD998443
Lash adjuster holder (8)
MD998443-01
Supporting of the lash
adjuster to prevent it from
falling when rocker shaft
assembly is removed or
installed
B991502
MB991453
MZ203827
D998443
SPECIAL TOOLS
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-4
MB990767
End yoke holder
MB990767-01
Holding the camshaft
sprocket and crankshaft
pulley when loosening and
tightening bolt
MD998715
Crankshaft pulley holder
pin
MIT308239
MD998713
Camshaft oil seal installer
MD998713-01
Camshaft oil seal
installation
MB991559
Camshaft oil seal installer
adapter
−
Camshaft oil seal
installation (left bank side)
(Use with MD998713)
MD998717
Crankshaft front oil seal
installer
MD998717-01
Crankshaft front oil seal
installation
MD998781
Flywheel stopper
General service tool
Flywheel <M/T> or drive
plate <A/T> supporting
MD998718
Crankshaft rear oil seal
installer
MD998718-01
Crankshaft rear oil seal
installation
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB990767
D998715
D998713
B991559
D998717
D998781
D998718
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст