Mitsubishi Galant. Manual — part 725
HEATER CONTROL ASSEMBLY AND A/C SWITCH
TSB Revision
HEATING AND AIR CONDITIONING
55-26
•
Lights, electric cooling fan and accessories: Set to OFF
•
Transmission: Neutral (N or P for vehicles with A/T)
•
Steering wheel: Straightforward
2. Check whether or not the idle speed is the standard value.
<2.4L Engine>: Refer to GROUP 13A, On-vehicle Service
−
Basic Idle Speed Adjustment
<3.0L Engine>: Refer to GROUP 13B, On-vehicle Service
−
Basic Idle Speed Adjustment
Standard value:
••••
<2.4L engine> 750 + 100 r/min
••••
<3.0L engine> 700 + 100 r/min
NOTE: Check 4 minutes after idling begins.
3. When the A/C is running after turning the A/C switch to ON,
and the blower switch to the 3(MH) or 4(HI) position, check
to be sure that the idle speed is at the standard value.
Standard value: 850
±±±±
100 r/min
NOTE: The engine control module <M/T>/the powertrain
control module <A/T> determines whether the A/C load is
low or high according to the output signal from the automatic
compressor controller.
NOTE: It is not necessary to make an adjustment, because
the idling speed is automatically adjusted by the ISC
system. If, however, a deviation from the standard value
occurs for some reason, check the ISC system.
NOTE: Check 4 minutes after idling begins.
HEATER C O N TR O L A SSEM B LY A N D A /C SWITC H
HEATER CONTROL ASSEMBLY AND A/C SWITCH
M1552002400068
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
•
Center Panel Assembly, Front Driver's Side
Under Cover and Front Passenger's Side Under
Cover Removal and Installation (Refer to
GROUP 52A, Instrument Panel
.)
•
Radio and Tape Player Removal and Installation
(Refer to GROUP 54A, Audio System - Radio
and Tape Player, CD Player and CD Auto
Changer
.)
•
Floor Console Removal and Installation (Refer to
GROUP 52A, Floor Console
.)
•
Instrument Panel Center Reinforcement Removal
and Installation (Refer to GROUP 52A,
Instrument Panel
•
Foot Duct (LH) Removal and Installation (Refer to
HEATER CONTROL ASSEMBLY AND A/C SWITCH
TSB Revision
HEATING AND AIR CONDITIONING
55-27
REMOVAL SERVICE POINTS
<<A>> HEATER CONTROL ASSEMBLY REMOVAL
After disconnecting the heater/cooler unit side connections of
the air mix damper lever cable and air outlet changeover link
cable, remove the heater control assembly.
AC02943
1
2
3
4
5
6
7
8
10
9
AC
REMOVAL STEPS
<<A>>
>>A<<
1.
HEATER CONTROL ASSEMBLY
2.
KNOB ASSEMBLY
3.
BULB HARNESS
4.
DEFROSTER SWITCH
<<B>>
5.
AIR MIX DAMPER LEVER CABLE
<<B>>
6.
AIR OUTLET CHANGEOVER
DAMPER LINK CABLE
7.
HEATER CONTROL PANEL
8.
BLOWER SWITCH ASSEMBLY
9.
BULB
REMOVAL STEPS (Continued)
AC001394AB
HEATER
CONTROL
UNIT
AIR OUTLET
CHANGEOVER
LINK CABLE
AIR MIX
DAMPER
LEVER
CABLE
HEATER CONTROL ASSEMBLY AND A/C SWITCH
TSB Revision
HEATING AND AIR CONDITIONING
55-28
<<B>> AIR MIX DAMPER LEVER CABLE, AIR OUTLET
CHANGEOVER DAMPER LINK CABLE REMOVAL
Insert a flat-tipped screwdriver into the control base clip from
inner side, and then remove the cable by lifting the claw part of
the clip.
INSTALLATION SERVICE POINT
>>A<< HEATER CONTROL ASSEMBLY INSTALLATION
1. Follow the steps below to install the air outlet changeover
damper link cable.
(1) Set the air outlet changeover control knob on the heater
control assembly to the defroster position.
(2) Set the air outlet changeover damper link of the heater/
cooler unit to the defroster position as shown in the
illustration, and then connect the cable to the link pin.
(3) Push the outer cable in the direction so that there is no
looseness, and then secure it with the clip.
2. Follow the steps below to install the air mix damper lever
cable.
(1) Set the temperature control knob on the heater control
assembly to the maximum hot position.
(2) Set the air mix damper lever of the heater/cooler unit to
the maximum hot position as shown in the illustration,
and then connect the cable to the lever pin.
(3) Push the outer cable in the direction so that there is no
looseness, and then secure it with the clip.
3. After installation, ensure that each damper operates
smoothly by operating the heater control assembly knob.
AC001395
FLAT-TIPPED
SCREWDRIVER
CLAW
PART
AB
AC001396
AIR OUTLET
CHANGEOVER
DAMPER LINK
DEFROSTER
POSITION
FACE
POSITION
AB
AC001397
MAXIMUM HOT
POSITION
MAXIMUM COOL
POSITION
AIR MIX
DAMPER
LEVER
AB
HEATER CONTROL ASSEMBLY AND A/C SWITCH
TSB Revision
HEATING AND AIR CONDITIONING
55-29
INSPECTION
M1552002500043
DEFROSTER SWITCH CONTINUITY CHECK
BLOWER SWITCH ASSEMBLY CONTINUITY
CHECK
1. BLOWER SWITCH
2. A/C SWITCH
3. INSIDE/OUTSIDE AIR CHANGEOVER SWITCH
AIR OUTLET
CHANGEOVER
CONTROL KNOB
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
DEFROSTER,
DEFROSTER/
FOOT
2-3
Continuity
OTHER POSITION 1-3
Continuity
AC001398
HEATER
CONTROL
ASSEMBLY
AB
SWITCH
POSITION
TESTER
CONNECTION
(CONNECTOR A)
SPECIFIED
CONDITION
0 (OFF)
-
No continuity
1 (LO)
3-5
Continuity
2 (ML)
1-3
Continuity
3 (MH)
3-6
Continuity
4 (HI)
3-4
Continuity
SWITCH
POSITION
TESTER
CONNECTION
(CONNECTOR B)
SPECIFIED
CONDITION
Off
-
No continuity
On
5-6-7
Continuity
SWITCH
POSITION
TESTER
CONNECTION
(CONNECTOR B)
SPECIFIED
CONDITION
Off
1-3
Continuity
On
2-3-4
Continuity
AC001399
CONNECTOR A
CONECTOR B
OFF
ON
OFF
ON
A/C SWITCH
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст