Mitsubishi Galant. Manual — part 457
SPECIFICATIONS
TSB Revision
AUTOMATIC TRANSAXLE
23A-295
<<F>> DRIVE PLATE BOLTS/TRANSAXLE ASSEMBLY
LOWER PART COUPLING BOLTS/TRANSAXLE ASSEMBLY
REMOVAL
1. Support the transaxle assembly by using a transaxle jack.
2. Remove the drive plate bolts while turning the crank shaft.
3. Press in the torque converter to the transaxle side so that
the torque converter does not stay engaged to the drive
plate.
4. Remove the transaxle assembly lower bolts and lower the
transaxle assembly.
INSTALLATION SERVICE POINTS
>>A<< TRANSAXLE ASSEMBLY INSTALLATION
Inserting the torque converter into the transaxle oil pump so
that the shown dimension is approximately. 12.2 mm (0.48
inch) <2.4L ENGINE>, approximately 9.4 mm (0.37 inch) <3.0L
ENGINE>. Install the transaxle assembly to the engine.
>>B<< TRANSAXLE MOUNT STOPPER INSTALLATION
Install the transaxle mount stopper so that the arrow mark
points as shown in the illustration.
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1231012400063
AC001645AB
DRIVE PLATE BOLT
AC001646AB
APPROXMATELY
12.2 mm (0.48 in)
<2.4L ENGINE>
9.4 mm (0.37 in)
<3.0L ENGINE>
AC001647AB
TRANSAXLE
MOUNT
STOPPER
ENGINE SIDE
ARROW
TRANSAXLE
MOUNT
BRACKET
ITEMS
SPECIFICATIONS
Key interlock cable
11 N
⋅
m (97 in-lb)
Shift lock cable
11 N
⋅
m (97 in-lb)
Transaxle assembly
Bell housing cover <2.4L engine>
To engine
8.8 N
⋅
m (78 in-lb)
To transaxle
26 N
⋅
m (19 ft-lb)
SPECIFICATIONS
TSB Revision
AUTOMATIC TRANSAXLE
23A-296
SERVICE SPECIFICATIONS
M1231000300047
Centermember assembly
Front
93 N
⋅
m (69 ft-lb)
Front roll stopper
45 N
⋅
m (33 ft-lb)
Rear
74 N
⋅
m (53 ft-lb)
Drive plate bolt
49 N
⋅
m (37 ft-lb)
Drive shaft and inner shaft <3.0L engine>
40 N
⋅
m (30 ft-lb)
Lower arm connection
108 N
⋅
m (80 ft-lb)
Rear roll stopper bracket
45 N
⋅
m (34 ft-lb)
Transaxle control cable connection
11 N
⋅
m (97 in-lb)
Starter motor
30 N
⋅
m (23 ft-lb)
Starter cover mounting bolt <2.4L engine>
4.9 N
⋅
m (44 in-lb)
Stabilizer link connection
44 N
⋅
m (33 ft-lb)
Tie rod end connection
29 N
⋅
m (21 ft-lb)
Transaxle assembly lower part cou-
pling bolt
2.4L engine
48 N
⋅
m (36 ft-lb)
3.0L engine
71 N
⋅
m (52 ft-lb)
Transaxle assembly upper part cou-
pling bolt
2.4L engine
48 N
⋅
m (36 ft-lb)
3.0L engine
Bolt, flange
71 N
⋅
m (52 ft-lb)
Bolt, washer assembled 88 N
⋅
m (65 ft-lb)
Transaxle mount bracket
57 N
⋅
m (42 ft-lb)
Transaxle mount stopper
83 N
⋅
m (61 ft-lb)
Transaxle control
Detent spring
1.5 N
⋅
m (14 in-lb)
Indicator panel assembly
1.5 N
⋅
m (14 in-lb)
Key interlock cable connection
11 N
⋅
m (97 in-lb)
Lever assembly
11 N
⋅
m (97 in-lb)
Nut
11 N
⋅
m (97 in-lb)
Shift lock cable connection
11 N
⋅
m (97 in-lb)
Shift knob
1.8 N
⋅
m (16 in-lb)
Selector lever assembly
11 N
⋅
m (97 in-lb)
Transaxle control cable assembly
11 N
⋅
m (97 in-lb)
ITEMS
SPECIFICATIONS
ITEMS
STANDARD VALUE
Line pressure kPa (psi)
1,010
−
1,050 (147
−
152)
A/T fluid temperature sensor k
Ω
at 0
°
C (32
°
F)
16.7
−
20.5
at 20
°
C (68
°
F)
7.3
−
8.9
at 40
°
C (104
°
F)
3.4
−
4.2
at 60
°
C (140
°
F)
1.9
−
2.2
at 80
°
C (176
°
F)
1.0
−
1.2
at 100
°
C (212
°
F)
0.57
−
0.69
Resistance of torque converter clutch control solenoid valve coil [at 20
°
C
(68
°
F)]
Ω
2.7
−
3.4
SPECIFICATIONS
TSB Revision
AUTOMATIC TRANSAXLE
23A-297
LUBRICANTS
M1231000400055
Resistance of low-reverse solenoid valve coil [at 20
°
C (68
°
F)]
Ω
2.7
−
3.4
Resistance of second solenoid valve coil [at 20
°
C (68
°
F)]
Ω
2.7
−
3.4
Resistance of underdrive solenoid valve coil [at 20
°
C (68
°
F)]
Ω
2.7
−
3.4
Resistance of overdrive solenoid valve coil [at 20
°
C (68
°
F)]
Ω
2.7
−
3.4
Stall speed r/min
2,100
−
2,600
ITEMS
STANDARD VALUE
ITEMS
SPECIFIED LUBRICANTS
QUANTITY
A/T fluid dm
3
(qt)
F4A42
DIAMOND ATF SP III, ATF SP II M or
equivalent
7.8 (8.2)
F4A51
8.5 (9.0)
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст