Mitsubishi Galant. Manual — part 140
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-241
STEP 9. Check the output voltage at fuel tank differential
pressure sensor connector D-11.
(1) Disconnect fuel tank differential pressure sensor connector
D-11.
(2) Use special tool (MB991658) to connect terminals 2 and 3
of the disconnected sensor connector and those of the
harness side connector, respectively.
(3) Turn the ignition switch to the "ON" position.
(4) Remove the fuel cap.
(5) Measure the voltage between terminal 1 and ground by
backprobing.
•
Voltage should be between 2.0 and 3.0 volts.
(6) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading within the specified value?
YES : Check connectors D-15, C-71, C-17, C-41 and repair
or replace as required. Refer to GROUP 00E,
Harness Connector Inspection
. If connectors
D-15, C-71, C-17, C-41 are in good condition, check
the harness between fuel tank differential pressure
sensor connector D-11 and PCM connector C-41 for
short circuit to ground, then repair if necessary. Then
go to Step 26.
NO : Replace the fuel tank differential pressure sensor.
Then go to Step 26.
STEP 10. Check the output circuit voltage at PCM
connector C-41.
(1) Do not disconnect the PCM connector C-41.
(2) Turn the ignition switch to the "ON" position.
(3) Remove the fuel cap.
(4) Measure the voltage between terminal 92 and ground by
backprobing.
•
Voltage should be between 2.0 and 3.0 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading within the specified value?
YES : Go to Step 18.
NO : Check connectors D-15, C-71, C-17, C-41 and repair
or replace as required. Refer to GROUP 00E,
Harness Connector Inspection
. If connectors
D-15, C-71, C-17, C-41 are in good condition, check
the harness between intermediate connector D-15
and PCM connector C-41 for open circuit or damage.
Then repair if necessary. Then go to Step 26 .
ACX01760AB
MB991658
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
AC004962 AB
C-41
HARNESS SIDE
CONNECTOR
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-242
STEP 11. Check the 5-volt supply circuit voltage at PCM
connector C-40.
(1) Do not disconnect PCM connector C-40.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 46 and ground by
backprobing.
•
Voltage should be between 4.8 and 5.2 volts.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading within the specified value?
YES : Check connectors D-15, C-71, C-17, C-40 and repair
or replace as required. Refer to GROUP 00E,
Harness Connector Inspection
. If connectors
D-15, C-71, C-17, C-40 are in good condition, check
the harness between intermediate connector D-15
and PCM connector C-40 for open circuit or damage.
Then repair if necessary. Then go to Step 26 .
NO : Go to Step 12.
STEP 12. Check PCM connector C-40 for damage.
(1) Disconnect PCM connector C-40.
Q: Is there any failure at PCM connector C-40?
YES : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
NO : Go to Step 13.
STEP 13. Check the sensor power supply line for short
circuit to ground at PCM connector C-40.
(1) Disconnect PCM connector C-40 and measure at the
harness side.
(2) Check for the continuity between terminal 46 and ground.
•
There should be 2 ohms or more.
Q: Does the multi-meter reading exceed the specified
value?
YES : Go to Step 26.
NO : Go to Step 14.
AC004963AB
C-40
HARNESS SIDE
CONNECTOR
AC005043
CONNECTOR : C-40
PCM
AC
AC004964 AB
C-40
HARNESS SIDE
CONNECTOR
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-243
STEP 14. Check the sensor power supply lines.
(1) Check all the sensor power supply lines for damage, which
flow through the harness PCM connector (terminal 46.)
Q: Is there any failure in the sensor power supply lines?
When a failure is found : Repair if necessary. (Refer to
GROUP 90, Circuit Diagrams
−
MFI System <2.4L
STEP 15. Check the ground circuit voltage at PCM
connector C-40.
(1) Do not disconnect PCM connector C-40.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 57 and ground by
backprobing.
•
Voltage should be 0.5 volts or less.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the multi-meter reading below the specified value?
YES : Check connectors D-15, C-71, C-17, C-40 and repair
or replace as required. Refer to GROUP 00E,
Harness Connector Inspection
. If connectors
D-15, C-71, C-17, C-40 are in good condition, check
the harness between intermediate connector D-15
and PCM connector C-40 for open circuit or damage.
Then repair if necessary. Then go to Step 26 .
NO : Go to Step 16.
STEP 16. Check PCM connector C-40 for damage.
(1) Disconnect PCM connector C-40.
Q: Is there any failure at PCM connector C-40?
YES : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
NO : Go to Step 26.
AC004965 AB
C-40
HARNESS SIDE
CONNECTOR
AC005043
CONNECTOR : C-40
PCM
AC
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-244
STEP 17. Check the harness between fuel tank differential
pressure sensor connector D-11 and intermediate
connector D-15 for open circuit or damage.
(1) Disconnect fuel tank differential pressure sensor connector
D-11 and intermediate connector D-15.
Q: Is there any failure between fuel tank differential
pressure sensor connector D-11 and intermediate
connector D-15?
YES : Repair it. Then go to Step 26.
NO : Check connectors D-11, D-15 and repair or replace as
required. Refer to GROUP 00E, Harness Connector
Inspection
STEP 18. Check PCM connector C-41 for damage.
(1) Disconnect PCM connector C-41.
Q: Is there any failure at PCM connector C-41?
YES : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 26.
NO : Go to Step 19.
AC002041AC
CONNECTOR: D-11
FUEL TANK DIFFERENTIAL
PRESSURE SENSOR
AC002549AC
CONNECTOR: D-15
INTERMEDIATE
CONNECTOR
AC005043
CONNECTOR : C-41
PCM
AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст