Mitsubishi Galant. Manual — part 699
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-191
STEP 2. Check the hazard warning light switch ground
circuit at the hazard warning light switch connector C-07.
(1)Disconnect the hazard warning light switch connector C-07
and measure at the harness side.
(2)Measure the resistance between terminal 2 and ground.
Q: Is the resistance less than 2 ohm?
YES : Go to Step 5.
NO : Go to Step 3.
STEP 3. Check hazard warning light switch connector C-07
for damage.
Q: Is hazard warning light switch connector C-07 in good
condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The hazard warning
light switch input signal should be able to be checked
and the functions, which are described in the
"Technical Description (comment)," should work
normally.
STEP 4. Check the harness wire between hazard warning
light switch connector C-07 and ground.
Q: Is the harness wire between hazard warning light switch
connector C-07 and ground in good condition?
YES : There is no action to be taken.
NO : Repair it. The hazard warning light switch input signal
should be able to be checked and the functions,
which are described in the "Technical Description
(comment)," should work normally.
4 3 2 1
AC002151AB
CONNECTOR C-07
(HARNESS SIDE)
AC003089 AJ
CONNECTOR: C-07
AC003089 AJ
CONNECTOR: C-07
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-192
STEP 5. Check the hazard warning light switch connector
C-07 and ETACS-ECU connector C-82 for damage.
Q: Are hazard warning light switch connector C-07 and
ETACS-ECU connector C-82 in good condition?
YES : Go to Step 6.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
. The hazard
warning light switch input signal should be able to be
checked and the functions, which are described in the
"Technical Description (comment)," should work
normally.
STEP 6. Check the harness wire between hazard warning
light switch connector C-07 and ETACS-ECU connector C-
82.
Q: Is the harness wire between hazard warning light switch
connector C-07 and ETACS-ECU connector C-82 in
good condition?
YES : Replace the ETACS-ECU. The hazard warning light
switch input signal should be able to be checked and
the functions, which are described in the "Technical
Description (comment)," should work normally.
NO : Repair it. The hazard warning light switch input signal
should be able to be checked and the functions,
which are described in the "Technical Description
(comment)," should work normally.
AC003089 AJ
CONNECTOR: C-07
AC003082AC
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-82
AC003089 AJ
CONNECTOR: C-07
AC003082AC
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-82
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-193
Inspection Procedure N-5: The fog light switch signal is not sent to the ETACS-ECU.
CIRCUIT OPERATION
The ETACS-ECU operates the fog lights according
to the input signal from the fog light switch.
TECHNICAL DESCRIPTION (COMMENT)
The fog lights will not work normally if the fog light
switch input signal is an error.
TROUBLESHOOTING HINTS
•
Malfunction of the fog light switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Test Harness Set
AC004237
Fog Light Switch Input Circuit
AC003089 AK
CONNECTORS: C-25, C-56
C-25
C-56
AC003082AC
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-82
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-194
STEP 1. Check the fog light switch.
Q: Is the fog light switch in good condition?
YES : Go to Step 2.
NO : Repair it. The fog light switch input signal should be
able to be checked and the fog lights should work
normally.
STEP 2. Check the fog light switch ground circuit at the
fog light switch connector C-25.
(1)Disconnect the fog light switch connector C-25 and
measure at the harness side.
(2)Measure the resistance between terminal 7 and ground.
Q: Is the resistance less than 2 ohm?
YES : Go to Step 5.
NO : Go to Step 3.
STEP 3. Check fog light switch connector C-25 for
damage.
Q: Is fog light switch connector C-25 in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The fog light switch
input signal should be able to be checked and the fog
light should work normally.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released
−
No continuity
Pressed
6
−
7
Continuity
AC003404
AC003396
CONNECTOR C-25
(HARNESS SIDE)
AB
AC003089 AL
CONNECTOR: C-25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст