Mitsubishi Galant. Manual — part 109
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-117
STEP 5. Check connector B-17, B-19, B-21, B-22 at injector
for damage.
Q: Is the connector in good condition?
YES : Go to Step 6.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
STEP 6. Check the injector.
(1) Disconnect each injector connector.
(2) Measure the resistance between injector side connector
terminal 1 and 2.
Standard value: 13
−−−−
16 ohm [at 20
°°°°
C (68
°°°°
F)]
Q: Is the resistance standard value?
YES : Go to Step 7.
NO : Replace the injector. Then go to Step 11.
STEP 7. Check connector C-39, C-41 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection (
AK000557 AB
B-21
B-19
B-17
B-22
CONNECTORS:B-17,B-19,B-21,B-22
AK000557 AB
B-21
B-19
B-17
B-22
CONNECTORS:B-17,B-19,B-21,B-22
AK000559
2
1
INJECTOR SIDE
CONNECTOR
AB
AK000280
CONNECTORS : C-39, C-41
C-39
C-41
PCM
AZ
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-118
STEP 8. Check for harness damage between heated
oxygen sensor (front) connector B-15 terminal 4 and PCM
connector C-41 terminal 71.
Q: Is the harness wire in good condition?
YES : Go to Step 9.
NO : Repair it. Then go to Step 11.
STEP 9. Check for harness damage between injector
connector and PCM connector.
a. Check the harness wire between injector connector B-22
terminal 2 and PCM connector C-39 terminal 1 when
checking No.1 cylinder.
b. Check the harness wire between injector connector B-21
terminal 2 and PCM connector C-39 terminal 9 when
checking No.2 cylinder.
c. Check the harness wire between injector connector B-19
terminal 2 and PCM connector C-39 terminal 24 when
checking No.3 cylinder.
d. Check the harness wire between injector connector B-17
terminal 2 and PCM connector C-39 terminal 2 when
checking No.4 cylinder.
Q: Is the harness wire in good condition?
YES : Go to Step 10.
NO : Repair it. Then go to Step 11.
AK000556 AB
CONNECTOR:B-15
AK000280
CONNECTOR : C-41
PCM
AY
AK000557 AB
B-21
B-19
B-17
B-22
CONNECTORS:B-17,B-19,B-21,B-22
AK000280
CONNECTOR : C-39
PCM
AW
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-119
STEP 10. Check the fuel pressure.
Refer to, Fuel Pressure Test(
Q: Is the fuel pressure normal?
YES : Replace the PCM. Then go to Step 11.
NO : Repair it. Then go to Step 11.
STEP 11. Test the OBD-II drive cycle.
(1) Carry out a test drive with the drive cycle pattern. Refer to,
Procedure 6
−
Other Monitor(
(2) Check the diagnostic trouble code (DTC).
Q: Is the DTC P0134 is output?
YES : Retry the troubleshooting.
NO : The inspection is complete.
MULTIPORT FUEL INJECTION(MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-120
DTC P0135: O
2
Sensor Heater Circuit Malfunction (sensor 1)
AK000465
3 4
1 2
3 4
1 2
RED-
WHITE
RED-
WHITE
RED-
WHITE
RED
BR
O
WN-WHITE
BATTERY
A-21X
3
4
1
2
HEATED OXYGEN
SENSOR(FRONT)
B-15
MU802605
1
2
3
4
TO ECM
OR PCM
TO ECM
OR PCM
POWERTRAIN CONTROL
MODULE(PCM)
3
C-39
(MU803784)
MFI
RELAY
2
3 4
5 6
7 8
9
11 12 13 14 15 16 17 18 19 20
30
21 22 23
24 25
26 27 28 29
3132 33
34 35
1
10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст