Mitsubishi Galant. Manual — part 413
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-119
•
Damaged harness, connector
•
Malfunction of the PCM
DIAGNOSIS
Required Special Tool:
MB991502: Scan Tool (MUT-II)
STEP 1. Check the brake pedal height.
Refer to GROUP 35A, On-vehicle Service
−
Brake Pedal
Check and Adjustment
Q: Is the height adjusted properly?
YES : Go to Step 2.
NO : Adjust it.
STEP 2. Using scan tool MB991502, check data list item 26:
Stoplight Switch.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Set scan tool MB991502 to data reading mode for item 26,
Stoplight Switch.
•
When the brake pedal is depressed, the display should
be "ON."
•
When the brake pedal is not depressed, the display
should be "OFF."
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : This malfunction is intermittent. Refer to GROUP 00,
How to Use Troubleshooting/Inspection Service
Points
−
How to Cope with Intermittent Malfunction
NO : Go to Step 3.
STEP 3. Check the stoplight switch as single part.
Refer to GROUP 35A, On-vehicle Service
−
Stoplight Switch
Check
.
Q: Is the switch normal?
YES : Go to Step 4.
NO : Replace the stoplight switch.Refer to GROUP 35A,
Brake Pedal
.
AC003081AC
MB991502
DATA LINK
CONNECTOR
ACX02208
BRAKE PEDAL
STOPLIGHT
SWITCH
AD
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-120
STEP 4. Check connector C-03 at stoplight switch for
damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 5. Check the switch output voltage at PCM
connector C-42 by backprobing.
(1) Do not disconnect connector C-42.
(2) Measure the voltage between terminal 123 and ground by
backprobing.
•
When the brake pedal is depressed, voltage should be
battery positive voltage.
•
When the brake pedal is not depressed, voltage should
be less than 1.0 volt.
Q: Is the voltage normal?
YES : Go to Step 8.
NO : Go to Step 6.
AC004287
CONNECTOR: C-03
AC
AC004197
PCM
AF
CONNECTOR: C-42
AC001812
C-42 CONNECTOR
HARNESS SIDE VIEW
AE
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-121
STEP 6. Check connectors C-42 at PCM, C-57 at joint
connector and C-66, C-17 at intermediate connector for
damage.
Q: Are the connectors in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC004197
PCM
AF
CONNECTOR: C-42
AC004287
CONNECTOR: C-57
AD
AC004344
CONNECTOR: C-66
CONNECTOR
BLOCK (LH)
C-66
AB
AC004308AB
CONNECTOR: C-17
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-122
STEP 7. Check harness for damage between stoplight
switch connector C-03 terminal 1 and PCM connector C-42
terminal 123.
Q: Is the harness wire in good condition?
YES : Repair it because of the connector and the harness
damage between output signal line of the stoplight
switch.
NO : Repair it.
STEP 8. Check connector C-42 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC004287
CONNECTOR: C-03
AC
AC004197
PCM
AF
CONNECTOR: C-42
AC004197
PCM
AF
CONNECTOR: C-42
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст