Mitsubishi Galant. Manual — part 533
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-13
STEP: 3. Check the harness wires between ABS-ECU
connector A-03 and data link connector C-23.
NOTE: After inspecting intermediate connector C-12, C-57
inspect the wire. If intermediate connector C-12, C-57 is
damaged, repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. If the connector has been
repaired, go to Step 5.
Q: Are any harness wires between ABS-ECU connector A-
03 and data link connector C-23 damaged?
YES : Repair them and then go to Step 5.
NO : Go to Step 4.
AC005077AB
CONNECTOR: C-12
AC005076AD
CONNECTOR: C-57
AC003695 AB
CONNECTOR: A-03
AC005076AC
CONNECTOR: C-23
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-14
STEP: 4.Check the harness wires between ABS-ECU
connector A-03 and ground.
Q: Are any harness wires between ABS-ECU connector A-
03 and ground damaged?
YES : Repair them and then go to Step 5.
NO : Replace the ABS-ECU and then go to Step 5.
STEP: 5. Check symptoms.
Q: Does the scan tool will now communicate with the TCL
system?
YES : This diagnosis is complete.
NO : Return to Step 1.
INSPECTION PROCEDURE 2
2
2
2 : When the ignition switch is turned "ON" (engine stopped or after
startup), the TCL indicator light does not illuminate.
NOTE: This diagnosis procedure is limited to cases where communication with the scan tool is possible
(ABS-ECU power supply is normal) and no diagnostic trouble code outputs.
AC003695 AB
CONNECTOR: A-03
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-15
AC003725
TCL Indicator Light Circuit
AB
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-16
CIRCUIT OPERATION
•
Power to the TCL indicator light is supplied from
the ignition switch. The ABS-ECU grounds the
circuit to turn the light ON.
•
The ABS-ECU illuminates the TCL indicator light
for 3 seconds while running self-check. This light
can be illuminated for 3 seconds upon startup or
key ON, engine stopped.
TECHNICAL DESCRIPTION (COMMENT)
The cause may be: an open circuit in the TCL
indicator light power supply circuit, a blown TCL
indicator light bulb or ABS-ECU.
TROUBLESHOOTING HINTS
•
Blown fuse
•
Damaged wiring harness or connector
•
Burnt out TCL indicator light bulb
•
Malfunction of the ABS-ECU
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
STEP 1. Check the power supply circuit at ABS-ECU
connector A-03.
(1) Disconnect connector A-03 and measure at the harness
side.
(2) Turn the ignition switch to "ON" position.
(3) The TCL indicator light should illuminate if terminal 13 is
grounded.
Q: Does the TCL indicator light illuminate?
YES : Replace the hydraulic unit (integrated with ABS-ECU)
and then go to Step 9.
NO : Go to Step 2.
AC003695 AB
CONNECTOR: A-03
AC005076AB
CONNECTOR: C-29
AC005077AB
CONNECTOR: C-12
AC003082AK
CONNECTORS: C-73, C-77
C-73
JUNCTION BLOCK
(FRONT VIEW)
C-77
AC003701AB
A-03 (HARNESS SIDE)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст