Mitsubishi Galant. Manual — part 694
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-171
STEP 10. Check the input signal (by using scan tool
MB991502).
Check the input signals from the following switches:
•
Ignition key reminder switch
•
Driver's and front passenger's switch
•
Door switches
•
Driver's and front passenger's door key cylinder switch
•
Driver's, front passenger's and rear door lock actuator
switch
•
Hood switch
•
Trunk lid latch switch
•
Trunk lid lock key cylinder switch
•
Transmitter
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1)Connect scan tool MB991502 to the data link connector.
(2)Check that the tone alarm of scan tool MB991502 sounds
when the input signal enters.
Q: Does the tone alarm of scan tool MB991502 sound when
the input signal enters?
YES : Replace the ETACS-ECU. The security indicator light
should illuminate, and the theft-alarm system should
be armed normally.
NO : Check the relevant input signal circuit. Refer to
.
STEP 11. Check the input signal (by using a voltmeter).
Check the input signals from the following switches:
•
Ignition key reminder switch
•
Driver's and front passenger's switch
•
Door switches
•
Driver's and front passenger's door key cylinder switch
•
Driver's, front passenger's and rear door lock actuator
switch
•
Hood switch
•
Trunk lid latch switch
•
Trunk lid lock key cylinder switch
•
Transmitter
(1)Use special tool MB991529 to connect a voltmeter between
ground terminal 4 or 5 and ETACS-ECU terminal 9 of the
data link connector.
(2)Check that the voltmeter indicator deflects once when the
input signal enters.
Q: Does the voltmeter indicator deflect?
YES : Replace the ETACS-ECU. The security indicator light
should illuminate, and the theft-alarm system should
be armed normally.
NO : Check the relevant input signal circuit. Refer to
.
AC003081 AB
16 PIN
MB991502
AC003083
16 PIN
AB
ETACS-ECU
TERMINAL
GROUNDED TERMINAL
MB991529
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-172
Inspection Procedure M-2: Theft-alarm system: Horn does not sound when the theft-alarm is
triggered.
Theft-alarm Horn Circuit
AC004217
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-173
CIRCUIT OPERATION
The ETACS-ECU will sound the theft-alarm horn and
horn if the theft-alarm system or the keyless entry
system answerback is triggered.
TECHNICAL DESCRIPTION (COMMENT)
The theft-alarm horn is shared by the keyless entry
system. If the theft-alarm horn sounds normally
through the keyless entry system answerback, the
ETACS-ECU may be defective.
TROUBLESHOOTING HINTS
•
Malfunction of the theft-alarm horn
•
Malfunction of the theft-alarm horn relay
•
Malfunction of the ETACS-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tool:
•
MB991223: Test Harness Set
AC002299 AC
FUSIBLE LINK (1)
AC003128 AM
CONNECTOR: A-11X
THEFT-
ALARM
HORN
RELAY
BATTERY
AC003129 AF
CONNECTOR: A-23
AC003079 AB
CONNECTOR
BLOCK (LH)
CONNECTOR: C-66
AC003082AQ
JUNCTION BLOCK
(FRONT VIEW)
CONNECTORS: C-77, C-81
C-81
C-77
AC003080AF
JUNCTION BLOCK
(REART VIEW)
CONNECTOR: C-85
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-174
STEP 1. Check the keyless entry system horn answerback.
Activate the keyless entry system horn answerback. (Refer to
GROUP 42, Keyless Entry System
−
On-vehicle Service
−
Enabling/disabling the Answerback Function
Q: Does the horn answerback function work?
YES : Replace the ETACS-ECU. The horn should sound
when the theft-alarm system is triggered.
NO : Go to Step 2.
STEP 2. Check the theft-alarm horn.
Connect the battery as shown and check that the theft-alarm
horn sounds.
Q: Is the theft-alarm horn in good condition?
YES : Go to Step 3.
NO : Replace it. The horn should sound when the theft-
alarm system is triggered.
STEP 3. Check the theft-alarm horn relay.
Q: Is the theft-alarm horn relay in good condition?
YES : Go to Step 4.
NO : Replace it. The horn should sound when the theft-
alarm system is triggered.
STEP 4. Check the theft-alarm horn relay power supply
circuit at the theft-alarm horn relay connector A-11X.
(1)Disconnect the theft-alarm horn relay connector A-11X and
measure at the relay box side.
(2)Measure the voltages between terminals 3, 5 and ground.
Q: Are the voltages approximately 12 volts (battery
positive voltage)?
YES : Go to Step 7.
NO : Go to Step 5.
ACX02352
BATTERY
VOLTAGE
TESTER
CONNECTION
SPECIFIED
CONDITION
Not applied
1
−
3
Continuity
1
−
Battery (+)
terminal,
3
−
Battery (
−
)
terminal
4
−
5
Continuity
1
2 3
4
5
1
3
4
5
ACX01544
1
2
3
4
5
AC002148
CONNECTOR A-11X
(RELAY BOX SIDE)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст