Mitsubishi Galant. Manual — part 536
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-25
STEP 6. Check the continuity between the combination
meter and the ABS-ECU.
Check the continuity between combination meter connector C-
29 and ABS-ECU connector A-03.
Q: Is there the continuity between combination meter
connector C-29 and ABS-ECU connector A-03?
YES : Go to Step 9.
NO : Repair the harness wire and then go to Step 9.
STEP 7. Check connectors C-29, C-73, and C-78.
Check connectors C-29, C-73, and C-78 (Refer to GROUP
00E, Harness Connector Inspection
.).
Q: Are any of the connectors damaged?
YES : Repair it and then go to Step 9.
NO : Go to Step 8.
AC003695 AB
CONNECTOR: A-03
AC005076AB
CONNECTOR: C-29
AC005076AB
CONNECTOR: C-29
AC003082 AM
CONNECTORS: C-73, C-78
C-73
C-78
JUNCTION BLOCK
(FRONT VIEW)
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-26
STEP 8. Check the continuity between the ignition switch
(IG1) and the combination meter.
Q: Is there any continuity (less than 2 ohm) between the
ignition switch (IG1) and combination meter connector
C-29?
YES : Go to Step 9.
NO : Repair the harness wire and then go to Step 9.
STEP 9. Check symptoms
Q: Does the TCL warning light illuminate for 3 seconds
when the ignition switch is turned to the "ON" position
with engine stopped or upon startup?
YES : This diagnosis is complete.
NO : Return to Step 1.
INSPECTION PROCEDURE 4: The TCL indicator light remains illuminated after the engine is started
NOTE: This diagnosis procedure is limited to cases where communication with the scan tool is possible
(ABS-ECU power supply is normal) and no diagnostic trouble code outputs.
AC005076AB
CONNECTOR: C-29
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-27
AC003725
TCL Indicator Light Circuit
AB
TRACTION CONTROL SYSTEM (TCL) DIAGNOSIS
TSB Revision
TRACTION CONTROL SYSTEM (TCL)
35C-28
CIRCUIT OPERATION
•
The ABS-ECU controls the illumination of the
TCL indicator light by turning it "ON" and "OFF."
•
The ABS-ECU illuminates the TCL indicator light
on startup. If turns off the light after 3 seconds
when the ABS-ECU completes the self-check.
TECHNICAL DESCRIPTION (COMMENT)
The cause is probably the hydraulic unit (integrated
with ABS-ECU) malfunction.
TROUBLESHOOTING HINTS
•
Damaged wiring harness
•
Malfunction of the hydraulic unit (integrated with
ABS-ECU)
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
STEP 1. Check the power supply circuit at the ABS-ECU
connector A-03.
(1) Disconnect ABS-ECU connector A-03.
(2) Turn the ignition switch to the "ON" position.
Q: Is the TCL indicator light illuminate?
YES : Go to Step 2.
NO : Replace the Hydraulic unit (integrated with ABS-ECU)
and then go to Step 3.
AC003695 AB
CONNECTOR: A-03
AC003082AK
CONNECTORS: C-73, C-77
C-73
JUNCTION BLOCK
(FRONT VIEW)
C-77
AC005076AB
CONNECTOR: C-29
AC005077AB
CONNECTOR: C-12
AC003695 AB
CONNECTOR: A-03
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст