Mitsubishi Galant. Manual — part 59
OIL PAN
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-21
O IL PA N
REMOVAL AND INSTALLATION
M1112002800086
REMOVAL SERVICE POINTS
<<A>> LOWER OIL PAN REMOVAL
1. Remove the oil pan, lower mounting bolts.
Pre-removal and Post-installation operation
•
Engine Oil Draining and Refilling (Refer to GROUP 12,
On-vehicle Service
−
Engine Oil Replacement
.)
•
Front Exhaust Pipe Removal and Installation (Refer to
GROUP 15, Exhaust Pipe and Main Muffler
.)
AC001723 AC
48 N·m
35 ft-lb
26 – 33 N·m
19 – 24 ft-lb
26 – 33 N·m
19 – 24 ft-lb
35 N·m
26 ft-lb
5.9 N·m
52 in-lb
9.8 – 12 N·m
87 – 106 in-lb
39 N·m
29 ft-lb
1
2
3
4
5
6
7
8
9
7
9
SEALANT:
MITSUBISHI GENUINE PART
NO. MD970389 OR
EQUIVALENT
(ENGINE OIL)
GROOVE
BOLT HOLE
Ø 4 mm
(0.2 in)
LOWER OIL PAN REMOVAL
STEPS
1.
DRAIN PLUG
>>C<<
2.
DRAIN PLUG GASKET
<<A>>
>>B<<
7.
LOWER OIL PAN
UPPER OIL PAN REMOVAL
STEPS
1.
DRAIN PLUG
>>C<<
2.
DRAIN PLUG GASKET
3.
STARTER CONNECTOR
4.
STARTER
5.
OIL DIPSTICK AND DIPSTICK
GUIDE
6.
O-RING
<<A>>
>>B<<
7.
LOWER OIL PAN
8.
COVER
<<B>>
>>A<<
9.
UPPER OIL PAN
UPPER OIL PAN REMOVAL
STEPS (Continued)
OIL PAN
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-22
CAUTION
Do not use the oil pan remover (MD998727). It will damage
the upper oil pan.
2. Place a wooden block against the lower oil pan as shown in
the illustration and remove by tapping with a hammer.
<<B>> UPPER OIL PAN REMOVAL
1. Remove the upper oil pan mounting bolts.
2. Screw the bolts (M10) securing the upper oil pan to the
transaxle assembly in the illustrated bolt holes, then remove
the upper oil pan.
INSTALLATION SERVICE POINTS
>>A<< UPPER OIL PAN INSTALLATION
CAUTION
The bolt holes for bolts 13 and 14 in the illustration are cut
away on the transaxle side. Be careful not to insert these
bolts at an angle.
Tighten the oil pan, upper mounting bolts in the order shown.
AC001724
LOWER OIL PAN
AB
AC001725
AC001726AB
1
4
8
5
12
9
2
3
7
11
6
10
16
15
13
14
UPPER OIL PAN
REAR OIL
SEAL CASE
TRANSAXLE
SIDE
OIL PAN
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-23
>>B<< LOWER OIL PAN INSTALLATION
Tighten the lower oil pan mounting bolts in the order shown.
>>C<< DRAIN PLUG GASKET INSTALLATION
Replace the gasket with a new gasket. Install the new gasket in
the direction shown in the illustration.
INSPECTION
M1112002900083
•
Check the oil pan for cracks.
•
Check the oil pan sealant-coated surface for damage and
deformation.
AC001727
1
2
3
4
5
6
7
8
9
10
AB
ACX00364
DRAIN PLUG
GASKET
OIL PAN
SIDE
AB
CRANKSHAFT FRONT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-24
C R A N KSH A FT FR O N T O IL SEA L
REMOVAL AND INSTALLATION
M1112003400111
Required Special Tool:
•
MD998717: Crankshaft Front Oil Seal Installer
INSTALLATION SERVICE POINTS
>>A<< CRANKSHAFT FRONT OIL SEAL INSTALLATION
1. Apply a small amount of engine oil to the oil seal lip and then
insert.
2. Using special tool MD998717, tap the oil seal into the front
case.
Pre-removal and Post-installation Operation
•
Timing Belt Removal and Installation (Refer to
.)
AC001728 AC
8.8 N·m
78 in-lb
1
2
3
4
5
6
6
ENGINE OIL
REMOVAL STEPS
>>B<<
1.
CRANKSHAFT SPROCKET
2.
CRANKSHAFT POSITION
SENSOR
>>B<<
3.
CRANKSHAFT SENSING BLADE
>>B<<
4.
CRANKSHAFT SPACER
5.
KEY
>>A<<
6.
CRANKSHAFT FRONT OIL SEAL
REMOVAL STEPS (Continued)
ACX00363 AB
OIL SEAL
MD998717
CRANKSHAFT
MD998717
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст