Mitsubishi Galant. Manual — part 707
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-223
STEP 5. Check the harness wires between driver's door
lock actuator switch connector E-15 and ground.
NOTE: After checking intermediate connector C-68, check the
wires. If intermediate connector C-68 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
.
Q: Are the harness wires between driver's door lock
actuator switch connector E-15 and ground in good
condition?
YES : There is no action to be taken.
NO : Repair them. The input signal from the driver's door
lock actuator switch should be able to be checked and
the functions, which are described in the "Technical
Description (comment)," should work normally.
STEP 6. Check the driver's door lock actuator switch
connector E-15 and ETACS-ECU connector C-81 for
damage.
Q:
YES : Go to Step 7.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
. The input
signal from the driver's door lock actuator switch
should be able to be checked and the functions,
which are described in the "Technical Description
(comment)," should work normally.
AC003086AI
DOOR
CONNECTOR: E-15
AC003079AK
CONNECTOR
BLOCK (LH)
CONNECTOR: C-68
AC003082 AJ
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-81
AC003086AI
DOOR
CONNECTOR: E-15
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-224
STEP 7. Check the harness wires between driver's door
lock actuator switch connector E-15 and ETACS-ECU
connector C-81.
NOTE: After checking intermediate connector C-68, check the
wires. If intermediate connector C-68 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
.
Q: Are the harness wires between driver's door lock
actuator switch connector E-15 and ETACS-ECU
connector C-81 in good condition?
YES : Replace the ETACS-ECU. The input signal from the
driver's door lock actuator switch should be able to be
checked and the functions, which are described in the
"Technical Description (comment)," should work
normally.
NO : Repair them. The input signal from the driver's door
lock actuator switch should be able to be checked and
the functions, which are described in the "Technical
Description (comment)," should work normally.
AC003082 AJ
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-81
AC003086AI
DOOR
CONNECTOR: E-15
AC003079AK
CONNECTOR
BLOCK (LH)
CONNECTOR: C-68
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-225
STEP 8. Check the front passenger's door lock actuator
switch.
Q: Is the front passenger's door lock actuator switch in
good condition?
YES : Go to Step 9.
NO : Replace it. The input signal from the front passenger's
door lock actuator switch should be able to be
checked and the functions, which are described in the
"Technical Description (comment)," should work
normally.
STEP 9. Check the front passenger's door lock actuator
switch ground circuit at front passenger's door lock
actuator switch connector E-07.
(1)Disconnect front passenger's door lock actuator switch
connector E-07 and measure at the harness side.
(2)Measure the resistance between terminal 3 and ground.
Q: Is the resistance less than 2 ohm?
YES : Go to Step 12.
NO : Go to Step 10.
STEP 10. Check front passenger's door lock actuator
switch connector E-07 for damage.
Q: Is front passenger's door lock actuator switch
connector E-07 in good condition?
YES : Go to Step 11.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection. The input signal from the front
passenger's door lock actuator switch should be able
to be checked and the functions, which are described
in the "Technical Description (comment)," should work
normally.
ROD POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
LOCK
1
−
3
No continuity
UNLOCK
2
−
3
Continuity
ACX02351
LOCK
UNLOCK
VIEW A
A
AB
5
4
3
2
1
6
ACX01604 AC
CONNECTOR E-07
(HARNESS SIDE)
AC003086AH
DOOR
CONNECTOR: E-07
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-226
STEP 11. Check the harness wires between front
passenger's door lock actuator switch connector E-07 and
ground.
NOTE: After checking intermediate connector C-72, check the
wires. If intermediate connector C-72 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
.
Q: Are the harness wires between front passenger's door
lock actuator switch connector E-07 and ground in good
condition?
YES : There is no action to be taken.
NO : Repair them. The input signal from the front
passenger's door lock actuator switch should be able
to be checked and the functions, which are described
in the "Technical Description (comment)," should work
normally.
STEP 12. Check the front passenger's door lock actuator
switch connector E-07 and ETACS-ECU connector C-81 for
damage.
Q:
YES : Go to Step 13.
NO : Repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
. The input
signal from the front passenger's door lock actuator
switch should be able to be checked and the
functions, which are described in the "Technical
Description (comment)," should work normally.
AC003086AH
DOOR
CONNECTOR: E-07
AC003415 AD
CONNECTOR: C-72
CONNECTOR
BLOCK (RH)
AC003082 AJ
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-81
AC003086AH
DOOR
CONNECTOR: E-07
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст