Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 68

OIL PAN AND OIL PUMP

TSB Revision

ENGINE OVERHAUL <3.0L ENGINE>

11D-43

>>F<< DRAIN PLUG GASKET INSTALLATION

CAUTION

If the gasket is installed in the wrong direction, oil leaks
will be occurred.
Install the drain plug gasket in the direction shown.

>>G<< OIL FILTER INSTALLATION
1. Clean the installation surface of the filter bracket.

2. Apply engine oil to the O-ring of the oil filter.

3. Install the oil filter to the bracket and tighten it to the

specified torque.

Tightening torque: 14

±

2 N

⋅

m (122

±

17 in-lb)

4. If no torque wrench can be used for tightening, follow the

following procedure.

(1) Screw in the oil filter until its O-ring contacts the oil filter

bracket.

(2) Tighten the oil filter 3/4 turn.

>>H<< OIL PRESSURE SWITCH INSTALLATION

CAUTION

Be careful not to block the oil passage with sealant.
1. Apply 3M



AAD Part number 8672 or equivalent to the

thread of oil pressure switch.

2. Tighten the switch to the specified torque.

Tightening torque: 10

±

2 N

⋅

m (87

±

17 in-lb)

AKX00726

DRAIN PLUG

OIL
PAN
SIDE

GASKET

OIL PAN

AB

AKX00692

BRACKET
SIDE

AB

AKX00688

OIL PAN AND OIL PUMP

TSB Revision

ENGINE OVERHAUL <3.0L ENGINE>

11D-44

INSPECTION

M1113008200030

OIL PUMP
1. Check the tip clearance.

Standard value: 0.06

−

0.18 mm (0.003

−

0.007 inch)

2. Check the side clearance.

Standard value: 0.04

−

0.10 mm (0.002

−

0.003 inch)

3. Check the body clearance.

Standard value: 0.10

−

0.18 mm (0.004

−

0.007 inch)

Limit: 0.35 mm (0.013 inch)

AKX00743

AKX00744

AKX00745

PISTON AND CONNECTING ROD

TSB Revision

ENGINE OVERHAUL <3.0L ENGINE>

11D-45

PISTO N A N D C O N N EC TIN G R O D

REMOVAL AND INSTALLATION

M1113008400045

AKX00729

7

9

4

5

3

2

1

6

8

10

12

11

51 ± 1 N·m
38 ± 1 ft-lb

AB

APPLY ENGINE OIL TO ALL
MOVING PARTS BEFORE
INSTALLATION.

REMOVAL STEPS
1. NUT

<<A>>

>>E<<

2. CONNECTING ROD CAP
3 CONNECTING ROD BEARING,

LOWER

>>D<<

4. PISTON AND CONNECTING ROD

ASSEMBLY

5. CONNECTING ROD BEARING,

UPPER

>>C<<

6. PISTON RING NO.1

>>C<<

7. PISTON RING NO.2

>>B<<

8. OIL RING

<<B>>

>>A<<

9. PISTON PIN
10.PISTON
11. CONNECTING ROD
12.BOLT

REMOVAL STEPS (Continued)

PISTON AND CONNECTING ROD

TSB Revision

ENGINE OVERHAUL <3.0L ENGINE>

11D-46

Required Special Tool:
MIT216941: Piston Pin Setting Tool

REMOVAL SERVICE POINTS

<<A>> CONNECTING ROD CAP REMOVAL
1. Mark the cylinder number on the side of the connecting rod

big end for correct reassembly.

2. Keep the removed connecting rods, caps, and bearings in

order according to the cylinder number.

AKX00734

CYLINDER
NUMBER

AB