Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 388
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-71
STEP 5. Check combination meter connector C-41 and C-
43.
Q: Is any connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Go to Step 6.
STEP 6. Check the harness wire between combination
meter connector C-41 and junction block connector C-104.
Q: Is any harness wire between combination meter
connector C-41 and junction block connector C-104
damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Go to Step 7.
AC003552 AI
CONNECTORS: C-41, C-43
C-41
C-43
AC003552 AE
CONNECTOR: C-41
AC001995 AW
CONNECTOR: C-104
JUNCTION BLOCK
(FRONT VIEW)
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-72
STEP 7. Check the combination meter.
(1) Remove the combination meter and measure at the
combination meter side. (Refer to GROUP 54A,
Combination Meter Assembly and Vehicle Speed Sensor
.)
(2) Measure the continuity between terminal 44 and 45 at
conductor C-41.
Q: Is the continuity less than 2 ohm?
YES : Go to Step 8.
NO : Replace the combination meter.
Refer to GROUP 54A, Combination Meter Assembly
and Vehicle Speed Sensor
Then check that the malfunction is eliminated.
STEP 8. Check the combination meter.
(1) Remove the combination meter and measure at the
combination meter side. (Refer to GROUP 54A,
Combination Meter Assembly and Vehicle Speed Sensor
.)
(2) Measure the continuity between terminal 52 at conductor C-
41 and terminal 1 at conductor C-43.
Q: Is the continuity less than 2 ohm?
YES : Go to Step 9.
NO : Replace the combination meter.
Refer to GROUP 54A, Combination Meter Assembly
and Vehicle Speed Sensor
Then check that the malfunction is eliminated.
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
AC002358AC
CONNECTOR C-41
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
16
15
14
13
12
11
8
10
9
7
6
5
4
3
2
1
AC002130
CONNECTOR C-41
CONNECTOR C-43
AD
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-73
STEP 9. Check the harness wire between combination
meter connector C-41 and C-43.
Q: Is any harness wire between combination meter
connector C-41 and C-43 damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Go to Step 10.
STEP 10. Check auto-cruise control-ECU connector C-20.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that the malfunction is eliminated.
NO : Go to Step 11.
STEP 11. Check the harness wire between combination
meter connector C-41 and auto-cruise control-ECU
connector C-20.
Q: Is any harness wire between combination meter
connector C-41 and auto-cruise control-ECU connector
C-20 damaged?
YES : Repair the harness wire and then check that the
malfunction is eliminated.
NO : Check that the malfunction is eliminated.
If the malfunction is eliminated, replace the auto-
cruise control-ECU. (Refer to
.)
Then check that the malfunction is eliminated.
AC003552 AI
CONNECTORS: C-41, C-43
C-41
C-43
AC001451
CONNECTOR: C-20
AB
AC003552 AE
CONNECTOR: C-41
AC001451
CONNECTOR: C-20
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-74
DATA LIST REFERENCE TABLE
M1172002400062
MUT-II SCAN
TOOL DISPLAY
ITEM
NO.
INSPECTION ITEM
INSPECTION
REQUIREMENT
NORMAL
CONDITION
CANCEL SWITCH
04
Auto-
cruise
control
switch
CANCEL
CANCEL switch: "ON"
ON
CANCEL switch: "OFF"
OFF
IDLE SW SIG
08Closed throttle
position switch
Accelerator pedal: Depressed
OFF
Accelerator pedal: Released
ON
MAIN SW
01
Auto-
cruise
control
switch
MAIN
MAIN switch: "ON"
ON
MAIN switch: "OFF"
OFF
OD OFF
15
A/T control signal
NO OD-OFF request
OFF
OD-OFF request
ON
PNP SW/CLUTCH
14
Clutch switch <M/T>
Clutch pedal: Depressed <M/
T>
ON
Clutch pedal: Released <M/T> OFF
Park/neutral position
switch <A/T>
Selector lever: "P" or "N"
position <A/T>
ON
Selector lever: Other than "P"
or "N" position <A/T>
OFF
RESUME SWITCH 03
Auto-
cruise
control
switch
RESUME RESUME switch: "ON"
ON
RESUME switch: "OFF"
OFF
SET SWITCH
02
SET
SET switch: "ON"
ON
SET switch: "OFF"
OFF
STOPLIGHT SW
05
Stoplight switch
Brake pedal: Depressed
ON
Brake pedal: Released
OFF
TP SENSOR
13
Throttle position
sensor
Ignition
switch:
"ON"
Accelerator pedal:
Fully depressed
300
−
1,000 mV
<2.4L>
537
−
735 mV
<3.0L>
Accelerator pedal:
Depressed
Increases in
proportion to throttle
opening angle.
Accelerator pedal:
Released
4,000
−
5,500 mV
VSS
10
Vehicle speed sensor Road test the vehicle
The speedometer and
MUT-II display the
same value.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст