Mitsubishi Eclipse / Eclipse Spyder (2000-2002). Service and repair manual — part 629
DOOR
TSB Revision
BODY
42-63
SPECIAL TOOLS
M1423000600070
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991502 Scan tool
(MUT-II)
DRB-III scan tool
ETACS-ECU input signal or
diagnostic trouble code
checking
MB991529 Diagnostic
trouble code check
harness
MB991529
ETACS-ECU input signal or
checking (when using a
voltmeter)
MB990900 or
MB991164 Door
adjusting wrench
MB990900-01
Adjustment of door fit
MB990784 Ornament
remover
General service tool
Removal of trim, etc.
MB991223 Harness set
•
A: MB991219 Test
harness
•
B: MB991220 LED
harness
•
C: MB991221 LED
harness adapter
•
D: MB991222 Probe
MB991223Measurement of terminal
voltage
•
A: Connector pin contact
pressure inspection
•
B: Power circuit inspection
•
C: Power circuit inspection
•
D: Commercial tester
connection
B991502
MB991529
MB990900
MB990784
MB991223
DOOR
TSB Revision
BODY
42-64
ON-VEHICLE SERVICE
DOOR FIT ADJUSTMENT
M1423000900059
CAUTION
•
Attach protection tape to the fender and door edges
where the hinge is installed.
•
Do not rotate special tool MB991164 with a torque of
over 98 N
⋅
m (72 ft-lb)
1. Use special tool MB990900 or MB991164 to loosen the
hinge mounting bolts on the body side, and then adjust the
clearance around the door so that it is uniform on all sides.
2. When there is a stepped section in the door and body, use
special tool MB990900 or MB991164 to loosen the hinge
mounting bolts on the door side, and ten adjust the door fit.
3. If the door opening and closing are stiff, adjust the linking of
the striker and the door latch using the shim, while moving
the striker up and down, or left and right.
DOOR WINDOW GLASS ADJUSTMENT
M1423001000060
1. Remove the door trim and waterproof film. (Refer to
2. Remove the drip line weatherstrip. <ECLIPSE> (Refer to
.)
3. Remove the topstack rail weatherstrip. <ECLIPSE
4. Loosen the bolts and nuts of the following parts.
•
Delta sash assembly
•
Power window regulator assembly
•
Glass carrier plate
•
Up-stop
•
Rear lower sash
5. Tighten the power window regulator assembly upper bolts
and the glass carrier plate mounting bolts so that the
clearances between the weatherstrip holder and the window
glass as well as between the door panel and the window
glass meet the respective standard values. (Sections A
−
A,
B
−
B, C
−
C, D
−
D, E
−
E, F
−
F.)
ACX00495
MB990900 OR
MB991164
AB
ACX00497AB
STRIKER
SHIM
AC000470
DELTA SASH
ASSEMBLY
UP-STOP
GLASS CARRIER
PLALE
REAR LOWER SASH
POWER WINDOW REGULATOR ASSEMBLY
AB
DOOR
TSB Revision
BODY
42-65
CAUTION
The right and left adjusting bolts should turned by the
same number of threads.
6. Turn the lower adjusting bolts (right and left) of the power
window regulator assembly until the clearances between the
weatherstrip and the window glass meet the respective
standard values. (Sections G
−
G, H
−
H, I
−
I, J
−
J.)
AC003391
A
A
B
B
C
C
D
D
E
E
F
F
SECTION A – A
<ECLIPSE>
SECTION B – B
<ECLIPSE SPYDER>
SECTION C – C
<ECLIPSE>
<ECLIPSE SPYDER>
SECTION D – D
<ECLIPSE>
SECTION E – E
SECTION F – F
<ECLIPSE>
2.9 ± 1.0 mm
(0.11 ± 0.44 in)
WEATHERSTRP
HOLDER
TOP COVER ASSEMBLY
WEATHERSTRIP HOLDER
5 mm
(0.20 in)
2.7 ± 1.0 mm
(0.11 ± 0.44in)
WEATHERSTRIP
HOLDER
QUARTER WINDOW
GLASS
FRONT DOOR
GLASS
8.7 mm
(0.34 in)
10.7 ± 1.0 mm
(0.42 ± 0.04 in)
WEATHERSTRIP
HOLDER
12.6 mm
(0.50 in)
5 mm
(0.20 in)
DOOR PANEL
12.6 mm
(0.50 in)
5 mm
(0.20 in)
DOOR PANEL
AB
DOOR
TSB Revision
BODY
42-66
7. Press the up-stop against the window glass stop, and then
tighten the up-stop nut.
8. Lower the window glass to the extreme position.
CAUTION
The adjusting bolts should be turned by the same number
of threads.
9. Tighten the adjusting bolts (upper and lower) until the rear
lower sash is positioned as shown in the illustration, and
then lock the nuts place.
10.Raise the window glass to the extreme position.
11.Turn the adjusting bolt until the gap between the delta sash
assembly and the window glass end meets the shown
dimension.
12.Lower the window glass.
13.Lock the adjusting bolt of the delta sash assembly with a nut
14.Tighten the two upper bolts at the delta sash assembly.
AC003392
G
G
H
H
I
I
J
J
SECTION G – G
<ECLIPSE>
SECTION H –H
<ECLIPSE SPYDER>
SECTION I – I
<ECLIPSE>
SECTION J – J
<ECLIPSE>
<ECLIPSE SPYDER>
LARGER
DIMENSION
ADJUSTING
BOLT
SMALLER
DIMENSION
WEATHERSTRIP
HOLDER
7.1 – 9.1 mm
(0.28 – 0.36 in)
WEATHERSTRIP HOLDER
20 mm (0.80 in)
WEATHERSTRIP
HOLDER
5.9 – 7.9 mm
(0.23 – 0.31 in)
WEATHER
STRIP
HOLDER
11.1 – 13.1 mm
(0.44 – 0.52 in)
QUARTER WINDOW
GLASS
FRONT DOOR
GLASS
2.0 mm (0.08 in)
AC000473
K
K
K
K
SECTION K –K
UP-STOP
WINDOW
GLASS
WINDOW
GLASS
STOP
AC
AC000474AC
L
L
L
L
SECTION L – L
REAR LOWER
SASH
WINDOW GLASS
14 mm (0.6 in)
11.5 mm
(0.45 in)
ADJUSTING
BOLT
AC000475
ADJUSTING BOLT
DELTA
SASH ASSEMBLY
TILTING
REARWARD
DELTA
SASH
ASSEMBLY
TILTING
FORWARD
0.5 – 1.5 mm
(0.02 – 0.06 in)
WINDOW
GLASS END
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст